Free generator · Runs in your browser

Gridfinity generator A place for everything.

Design Gridfinity bins with dividers, labels and scoops, and baseplates that fit your drawer and your printer bed, all to the open 42 mm specification.

  • Free and privateNo account, nothing uploaded
  • Bins and baseplatesDividers, labels, scoops, magnets
  • Fits your drawerPlates split to your bed size
  • Ready to sliceSTL and 3MF files

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Make

Part

Size

2.0 units

1 unit = 42 mm.

1.0 units
6.0 × 7 mm

Measure the inside of the drawer. The grid fills as many 42 mm cells as fit.

Baseplates larger than the bed are split into pieces.

Inside

2.0
1.0

Printed raised on the shelf, sized to fit.

A curved floor that lets small parts slide out.

0.95 mm

Baseplates are open frames; switch on magnet pockets for a solid base.

Base

Holes under each cell

Lets bins stack on top of each other.

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The system

    What Gridfinity is

    Gridfinity is an open, modular storage system designed by Zack Freedman. Bins sit in a baseplate on a 42 mm grid, so any bin fits anywhere and stacks on others. This generator builds bins and baseplates to the published dimensions, so they fit parts from other Gridfinity makers.

    1. Measure your drawer and generate a baseplate. It is split to fit your printer if needed.
    2. Design bins in whole grid units, with dividers, a label shelf and a scoop.
    3. Print and drop in. Bins lock into the plate and can be rearranged at will.

    Specification

    Gridfinity dimensions

    FeatureValueNotes
    Grid42 × 42 mmBins are 41.5 mm per unit, leaving 0.25 mm each side.
    Height unit7 mmA bin is height × 7 mm including the base, plus the stacking lip.
    Bin foot0.8 / 1.8 / 2.15 mm steps45°, vertical, 45°: 4.75 mm tall in all.
    Baseplate0.7 / 1.8 / 2.15 mm steps5 mm tall, open frame.
    Stacking lip4.4 mm tallMatches the foot of the bin above.
    Magnets6 × 2 mmHoles 6.5 mm across, 2.4 mm deep, 13 mm from each cell centre.

    Planning

    Fitting a drawer and a print bed

    Enter the inside width and depth of the drawer. The generator fits as many 42 mm cells as it can and reports the spare space, which you can fill with spacers. If the baseplate is bigger than your bed, it is split into pieces that each fit, laid out ready to print.

    Printing

    Print settings for bins and plates

    • Orientation: feet down. All overhangs are 45°, so no supports.
    • Layers: 0.2 mm is a good balance. Baseplates can go to 0.28 mm.
    • Walls: two or three perimeters. Bins need little or no infill in the walls.
    • Material: PLA is the usual choice. Use PETG for workshops that get warm.

    Questions, answered

    Will these bins fit other Gridfinity baseplates?

    Yes. They follow the open specification published by the community (42 mm grid, 7 mm height units, standard foot profile), so they mix with other Gridfinity parts.

    Why is my baseplate in several pieces?

    It is bigger than the printer bed you chose. The pieces butt together in the drawer; tape or a little glue keeps them aligned.

    What magnets do I need?

    6 mm across and 2 mm thick, the standard Gridfinity magnet.

    Can I use bins without a baseplate?

    Yes. They stand on a flat surface, and the stacking lip still lets them stack.

    Is Gridfinity free to use?

    Yes. Gridfinity is released under the MIT licence, and so are the reference models these dimensions come from.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-07. Community posts are one maker's experience, not a specification.

    1. Gridfinity gridfinity.xyz
    2. gridfinity-rebuilt-openscad: standard dimensions kennetek (MIT licence)
    3. Gridfinity unofficial specification Gridfinity community