Free generator · Runs in your browser

Ball bearing generator Prints already assembled.

Make ball, roller and gear bearings that come off the bed ready to turn, plus turntable rings, bushings and races for steel balls. Pick a standard size such as 608 or set your own bore, outside diameter and width.

  • Private by designNothing leaves this device
  • Six typesBall, roller, gear and more
  • No supportsGrooves stay within 45°
  • Ready to sliceClearance test included

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Type

Bearing type

Prints fully assembled: two races and a ring of balls, each ball standing on a small flat on the bed.

Prints fully assembled: double-cone rollers in V tracks. The easiest kind to print, and it takes side loads both ways.

Prints fully assembled: a sun, planets and a ring with herringbone teeth, so nothing can slide out sideways.

Two washers with a V track and loose balls between them, for turntables and lazy susans. Printed as separate parts.

A plain sleeve with oil grooves. No moving parts: the shaft turns inside it.

Printed races for real balls you already have. Measure a ball with calipers.

Make

Three small bearings with the same parts at three gaps. One, two or three nubs on the outside tell them apart. Print it first and use the tightest one that turns freely.

Size

Standard sizes are bore × outside diameter × width, from a bearing maker’s published table.

For a turntable ring this is the height of the whole stack.

0.30 mm

Start at 0.3 mm for a 0.4 mm nozzle and 0.2 mm layers. Parts fused? Use more. Rattles? Use less. About 0.15 mm suits steel balls.

Sets the thinnest wall and the smallest ball we allow.

Moving parts

Groove

The round groove leaves thicker walls and room for bigger balls. The V touches each ball at four points.

45 %

The flat’s width as a share of the ball’s. A wider flat sticks to the bed better; a narrower one rolls smoother.

Half the balls, with a loose spacer between each pair so they stay evenly spread.

Rollers are as tall as the bearing and as wide as the walls allow. Their 45° ends ride in V tracks.

5

Tooth counts are chosen for you: the biggest teeth that fit.

30 °

The herringbone angle. 30° prints easily and holds the parts in.

Balls

Measure a ball with calipers. Marbles and airsoft pellets work too.

A flat ring with a hole for each ball, so they stay evenly spread.

60

Fewer balls print faster. The ring never gets more than fit.

Measure a ball with calipers: sold sizes vary.

How the balls go in

Both races print whole. Line up the two notches and drop the balls in one at a time.

The outer race prints as two halves. Stack them round the balls and glue them, or press them into a housing.

Oil grooves
4

Bore and outside

Bore shape

From the flat to the far side of the shaft.

The bore size is the distance across the hex’s flats.

The keyway is the standard metric key size for the shaft (DIN 6885-1), for shafts over 6 and up to 50 mm.

0.20 mm

Added to the bore. Printed holes come out small: 0.2 mm is a snug push fit on most printers, 0 or less a press fit.

24

Spur teeth with a 20° pressure angle. The module is shown under the preview, so you can make a matching gear.

A 45° V round the outside for a cord or a rail.

2

A separate block with two screw holes that the bearing presses into.

0.15 mm

Added to the seat for the bearing’s outside.

Screw one washer to the base and the other to the turntable.

For mounting ears and the housing. 3.4 mm clears an M3 screw.

Preview and colours

Cuts a quarter away so you can see inside. Downloads are always whole.

Show

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The method

    How to make a 3D printed bearing

    A printed bearing comes off the bed already assembled: the races and the balls are separate pieces printed a small gap apart. Give it one firm twist and it turns.

    1. Pick a type: ball, roller or gear bearing, a turntable ring, a bushing, or races for steel balls.
    2. Pick a size: a standard size such as 608, or your own bore, outside diameter and width.
    3. Set the gap. Start at 0.3 mm. If you are not sure, print the clearance test first.
    4. Choose the bore and outside: a D-shaft or hex bore, a flange, teeth, ears or a housing.
    5. Download and print flat, as shown, with no supports. Then twist the races to break the parts free.

    Printed bearings are for light loads and low speeds: toys, turntables, spool rollers, displays and models. They are not a substitute for steel bearings in machines, vehicles or anything that carries a person.

    Types

    Which bearing to print

    TypeHow it printsGood for
    Ball bearingAssembled. Balls stand on a small flat on the bedSmall wheels, spinners, models
    Roller bearingAssembled. Double-cone rollers in V tracksThe easiest to print; takes side loads both ways
    Gear bearingAssembled. Herringbone sun, planets and ringStrong, smooth, cannot come apart sideways
    Turntable ringTwo washers, a cage and loose ballsLazy susans, display turntables, big diameters
    BushingOne sleeve with oil groovesSlow shafts, hinges, pivots
    Steel-ball bearingPrinted races, your own ballsThe smoothest and longest-lasting of the six

    The ball bearing also works as a turntable at large diameters, and prints in one piece. Roller bearings here have straight rollers; their 45° ends give them the two-way grip of a crossed roller bearing without printing rollers on a tilt.

    Sizes

    Standard metric bearing sizes

    These are the boundary dimensions of metric deep groove ball bearings: the bore, the outside diameter and the width. A printed bearing in one of these sizes fits the same seat and shaft, but its balls are a different size and it carries far less load.

    SizeBoreOutside diameterWidth
    6077 mm19 mm6 mm
    6088 mm22 mm7 mm
    6099 mm24 mm7 mm
    6255 mm16 mm5 mm
    6266 mm19 mm6 mm
    6277 mm22 mm7 mm
    6299 mm26 mm8 mm
    600010 mm26 mm8 mm
    600112 mm28 mm8 mm
    600215 mm32 mm9 mm
    600317 mm35 mm10 mm
    600420 mm42 mm12 mm
    600525 mm47 mm12 mm
    600630 mm55 mm13 mm
    620010 mm30 mm9 mm
    620112 mm32 mm10 mm
    620215 mm35 mm11 mm
    620317 mm40 mm12 mm
    620420 mm47 mm14 mm
    620525 mm52 mm15 mm
    620630 mm62 mm16 mm

    The ball size is worked out for you: the biggest ball that leaves walls your nozzle can print. A printed ball stands on the bed, so in a wide bearing the ring of balls sits near the bottom.

    Printing

    Printing tips and the gap

    • Gap: 0.3 mm is a good start for a 0.4 mm nozzle and 0.2 mm layers. Use 0.4 mm for a 0.6 mm nozzle. Thinner layers (0.12 to 0.16 mm) make rounder balls.
    • Clearance test: three small bearings at three gaps, marked with one, two and three nubs. Use the tightest gap that turns freely.
    • No supports. Grooves never overhang past 45°. Supports would weld the balls in.
    • First layer: too much squish joins the balls to the races. If they are stuck at the bottom, raise the nozzle a little or turn on elephant-foot compensation.
    • Free it after printing: let it cool, then twist the inner and outer race hard in opposite directions. A few turns and a drop of light oil or dry lubricant smooth it out.
    • Material: PLA and PETG both work. Nylon wears best for bushings.
    • Steel balls: measure one with calipers. Fill through the slot, then turn the races so the notches are apart.
    • Small parts: loose balls are a choking hazard. Not for children under 3.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits.

    Will it fit my printer?

    Choose your printer below the preview. Print-in-place bearings are one piece, so they must fit the bed; turntable rings are laid out as separate parts.

    How strong is a printed bearing?

    Strong enough for toys, turntables, spool rollers and models. We give no load or speed ratings. Plastic balls wear and warm up, so do not use a printed bearing where a failure could hurt someone or damage a machine.

    My bearing is stuck. What now?

    Twist harder first: a new bearing needs a firm crack to break free. If it will not move, print the clearance test and use a bigger gap, and check that the first layer is not squashed too wide.

    Why are the balls not perfectly round?

    Each printed ball has a small flat underneath so it can stand on the bed without supports. It rolls over the flat with a faint tick. For smooth running, use the steel-ball type.

    Can I sell bearings I print?

    The designs you make are yours. Don’t sell them as replacements for rated bearings, and we make no claims about load or safety. Loose balls are small parts, so check toy-safety rules before selling for children.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-13. Community posts are one maker's experience, not a specification.

    1. Deep groove ball bearings: dimension tables GMN
    2. Ball bearing standard dimensions table (excerpt from JIS B 1512-1) Miki Pulley
    3. Gear systems (planetary conditions) KHK Gears, Gear Technical Reference
    4. DIN 6885-1 parallel keys fasten.it
    5. Modeling with 3D printing in mind Prusa Research
    6. Print-in-place 3D printing: hinges, joints and moving parts Sovol