Free generator · Runs in your browser

Model railway accessory generator Any scale, Z to G.

Make buffer stops, platforms, track gauges, station signs, fences, benches, lamps, rerailers and tunnel portals, scaled to your track with gauges and clearances from the NMRA and NEM standards.

  • Private by designNothing leaves this device
  • Eight itemsTen scales, Z to G
  • No supportsEach piece prints as laid out
  • Ready to slicePlates filled for your printer

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Scale and track

Track gauges come from NMRA S-3.2 and NEM 010. OO models run on the same 16.5 mm track as HO.

Large scale ratio (all on 45 mm track)

The code is the rail height in thousandths of an inch: code 83 is 0.083 in (2.1 mm). It is printed on the track’s box.

Measure from the bottom of the rail to its top.

Rail top above the baseboard

Include any roadbed or cork under the track. Platforms and tunnel portals stand on the baseboard.

Item

Make
Buffer stop
1000 mm

Typical, not a standard: match the height of your stock’s couplers or buffers.

300 mm

Longer than your bed and it splits into equal pieces with dovetail joints.

4.0 m
Track centres

Four tabs at the NMRA S-3.2 limits for your scale. Not offered for the European O scales, which NMRA does not cover.

Typeface
350 mm

Typical station signs use letters a few hundred millimetres tall.

2
60 mm
2
2

Ramps between and beside the rails, leaving the NMRA S-3.2 flangeway next to each rail.

Tracks through the portal
1

Every copy is packed onto your printer’s plates.

Clearances

Platform height, offset and tunnel opening

RP-7.1 gives North American clearances for four eras. It also sets the track centres for spacing gauges and double-track portals.

Measure your widest stock: half its width plus a little room.

Colours

Preview

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The method

    How to make scale railway accessories

    Pick your scale and rail, choose an item, and every size follows: the gauge sets the buffer stop’s width and the rail slots, the rail code sets their height, and the clearances set the platform and tunnel opening. Preview it on a length of track, then download it laid out on your printer’s plates.

    1. Choose the scale and the rail code on your track’s box.
    2. Pick the item: a buffer stop, platform, gauges, sign, street furniture, rerailer or tunnel portal.
    3. Set the clearances from NMRA RP-7.1 for your era, or measure your own.
    4. Pick your printer below the preview. Long platforms split into interlocking pieces; copies fill the plates.

    Sizes

    Scales, gauges and clearances

    ScaleTrack gauge, NMRA S-3.2 (mm)NEM 010 gauge (mm)Track centres, classic era (mm)Platform height / edge offset, classic era (mm)
    Z (1:220)6.6 (6.5–6.8)6.5185.5 / 8.3
    N (1:160)9.0 (9.0–9.1)9257.6 / 11.4
    TT (1:120)12.0 (12.0–12.2)123310.2 / 15.2
    HO (1:87.1)16.5 (16.5–16.8)16.54514.0 / 21.0
    OO (1:76.2, on 16.5 mm track)16.5 (16.5–16.8)—5216.0 / 24.0
    S (1:64)22.5 (22.4–22.7)22.56219.1 / 28.6
    O (1:48, North America)31.8 (31.8–32.1)—8325.4 / 38.1
    O (1:45, Europe)—328827.1 / 40.6
    O (1:43.5, 7 mm scale)—329128.0 / 42.0
    G / large scale (45 mm track)45.0 (44.9–45.3)4517654.2 / 81.3

    Model sizes are real sizes divided by the scale’s ratio. NMRA S-3.2 gives the track gauge as a target with a minimum and maximum; NEM 010 gives one nominal gauge per scale. The clearance columns use the classic era (1920 to 1969) of NMRA RP-7.1, which is North American; British and European lines are often tighter, so choose Measured for them if in doubt. G here is 1:22.5; other large scale ratios on 45 mm track scale the same way.

    Rail codes follow NMRA RP-15.1: the code is the rail height in thousandths of an inch, so code 100 rail is 0.100 in (2.54 mm) tall and code 55 is 0.055 in (1.40 mm).

    Items

    What you can make

    ItemSized fromPrints
    Buffer stopGauge, rail code, beam heightUpright, no supports
    PlatformRP-7.1 platform height and offset, or measured; your lengthUpright, split into dovetailed pieces
    Track spacing gaugeRP-7.1 minimum track centres, or your ownKeys up, no supports
    Track gauge checkerS-3.2 G min, G max, C min and S maxFlat
    Station signLetter height, your text and typefaceFlat, face up
    Fences, benches, lampsTypical real sizes, scaledFences flat; benches and lamps upright
    Rerailer rampGauge, rail code, S-3.2 flangewayFlat, three pieces
    Tunnel portalRP-7.1 tunnel diagram, or a measured openingFlat, face up

    The buffer stops, signs and furniture use typical proportions we chose, not a published standard.

    Printing

    Printing tips

    • Small scales: Z and N details are often under 0.8 mm, which a 0.4 mm nozzle blurs. A 0.2 mm nozzle or a resin printer keeps them crisp.
    • Gauge checker: the tolerance between G min and G max is a few tenths of a millimetre. Print it flat, check each tab with calipers, and adjust your printer’s scale or horizontal expansion until they match.
    • Two colours on one nozzle: add a colour change where the coping, letters or border begin.
    • Platforms: the dovetail socket is 0.15 mm wider each side than the tab. If yours fit tightly, sand the tab.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits.

    Will it fit my printer?

    Choose your printer below the preview. Platforms split into pieces that fit; copies spread over as many plates as needed; a portal bigger than the bed can be cut with the STL splitter.

    Can I sell accessories I print?

    The designs you make are yours. The typefaces are open-licensed, which allows making physical products. We make no other claims: check the rules for anything you sell, and remember that small parts are not for young children.

    Are these official NMRA or NEM parts?

    No. The gauges and clearances are taken from the published NMRA and NEM documents listed below, but the items are not tested or approved by either body. Check fit on your own track.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-12. Community posts are one maker's experience, not a specification.

    1. S-3.2 Track, Standard Scale National Model Railroad Association
    2. S-1.2 List of Standard Scales National Model Railroad Association
    3. RP-15.1 Rail National Model Railroad Association
    4. RP-7.1 Tangent Track Centers and Clearance Diagrams National Model Railroad Association
    5. NEM 010 Maßstäbe, Nenngrößen, Spurweiten (scales and gauges) MOROP
    6. Model railway scales and gauges explained World of Railways
    7. SIL Open Font License SIL International