Free generator · Runs in your browser

Coaster generator A whole set, and its holder.

Make a set of coasters with patterns drawn for you, a monogram or your logo, a drip lip, drainage channels and a cork pad recess, plus a holder that fits the stack.

  • Private by designNothing leaves this device
  • Seven patternsPlus text, logos and outlines
  • No supportsEverything prints flat
  • Ready to sliceEach colour its own part

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Shape

Shape

Hexagons tile together: lay the set out as a honeycomb.

6
100 mm

Across a round coaster, the flats of a hexagon, or the longer side of your outline. Most drink coasters are 89–102 mm (3.5–4 in). Measure the base of your biggest mug.

4.0 mm

From the bottom to the top surface, not counting the lip or raised design.

Pattern

Tiles
8

How many times the mandala repeats around the centre.

9.0 mm

Cell size, or the spacing between lines.

1.4 mm

At least two nozzle widths (0.8 mm with a 0.4 mm nozzle) so every line prints solid.

3

Each number gives a different arrangement.

Text and logo

One or two lines. Short initials make the boldest monograms.

Each line of the text goes on its own coaster, such as a name or initial for each person.

50 %

Of the design area, before it shrinks to fit the width.

Typeface
60 %

Leaves a 1.2 mm gap so letters stand clear of the pattern.

Colours and inlay

Design style

Raised on the top: two colours on any printer with one colour change.

1.0 mm

Flush with the top as its own part, for a multi-material printer.

A recess in the coaster and separate pieces you print in another colour and press in. Best for monograms and logos.

1.0 mm
0.15 mm

Gap all round each piece. Raise it if pieces will not go in; lower it if they fall out.

Lip and underside

A raised rim that keeps condensation on the coaster.

1.4 mm
4.0 mm
Drainage channels
2.0 mm
1.0 mm

With an inlay, channels are as deep as the inlay.

14 mm
90 mm

The recess is 0.4 mm wider than this, and shrinks to fit the coaster if it is too big.

4.0 mm
2.0 mm
0.4 mm

So the coaster rests on the pad, not the plastic rim.

Set and holder

4
0.8 mm
2.4 mm
Preview

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The method

    How to make a coaster set

    Pick a shape and a pattern, add a monogram or a logo if you like, and the generator builds every coaster, the pieces for an inlay and a holder for the stack, then lays them all out on your printer’s plates.

    1. Pick the shape and size. Measure the base of your biggest mug first.
    2. Choose a top pattern, or none for a plain monogram.
    3. Add text or a logo; the pattern clears round it.
    4. Choose how the colours print: a colour swap, a multi-material inlay, press-fit pieces or engraved.
    5. Add the lip, channels and pad recess you want, set how many coasters, and download.

    Options

    Shapes, patterns and styles

    OptionChoicesGood for
    ShapeRound, square, rounded square, hexagon, flower, your outlineHexagons tile into a honeycomb on the table
    PatternVoronoi, honeycomb, waves, mandala, rings, topographic lines, geometric tilesVoronoi and topographic lines differ on every coaster
    RaisedDesign stands 0.4–2 mm above the topTwo colours on one nozzle: one colour change
    Flush inlayDesign flush with the top, its own partMulti-material printers
    Inlay piecesA recess plus separate press-fit piecesMonograms and logos in a second colour on any printer
    EngravedDesign cut into the topOne colour, or filled with paint

    Sizes

    Sizes that work

    SettingDefaultNotes
    Coaster size100 mmDrink coasters are commonly 89–102 mm (3.5–4 in). Go bigger for wide mugs.
    Thickness4 mmPlus the lip or raised design
    Line width1.4 mmTwo nozzle widths or more prints solid
    Pad recessMeasure your padDiameter and thickness of your own cork or felt pads
    Holder clearance0.8 mmEach side; raise it if coasters stick

    Printing

    Printing tips

    • No supports: everything prints flat, top up.
    • Colour swap: add the colour change at the height shown under the preview.
    • Fine lines: a 0.4 mm nozzle and 0.2 mm layers suit the default line width; for thin topographic lines use 0.12–0.16 mm layers.
    • Cork and felt: stick self-adhesive pads in the recess after printing.
    • Inlay pieces: print one test piece first and change the fit clearance to suit your printer.

    Safety

    Hot drinks and hot pans

    PLA gets soft and can deform above about 60 °C, so a hot mug can mark a PLA coaster. For hot drinks print in PETG, which suits use below about 80 °C. Printed plastic is not a trivet: never put hot pans, pots or oven dishes on a printed coaster. A coaster touches the cup, not your food or drink, and we make no food-safety claim for any print.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits.

    Will it fit my printer?

    Choose your printer below the preview. The coasters, inlay pieces and holder spread over as many plates as needed; lower the size if one coaster is too big for your bed.

    Can I sell coasters I print?

    The designs you make are yours, and the patterns are drawn by the generator. The typefaces are open-licensed, which allows making physical products. Only upload logos and pictures you have the rights to use.

    Can I use them for hot coffee?

    Print them in PETG rather than PLA for hot mugs. Do not use printed coasters under hot pans or dishes.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-10. Community posts are one maker's experience, not a specification.

    1. What size should my custom drink coasters be? 4OVER4
    2. PLA Prusa Research
    3. PETG Prusa Research
    4. Color change Prusa Research
    5. SIL Open Font License SIL International