Free generator · Runs in your browser

Iris box generator Twist the lid open.

Make a box whose lid opens like a camera aperture when you twist the top ring. Size it to what goes inside, choose 5 to 12 blades, add a name, and print every part without supports.

  • Private by designNothing leaves this device
  • 5 to 12 bladesWorked out to close fully
  • No supportsEvery part prints as laid out
  • Ready to sliceEach part its own object

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

What to make

Make

A box with a floor. Twist the ring on top and the lid opens like a camera aperture.

Two halves, each with its own iris, joined by a sleeve: a tube that opens at both ends.

Just the mechanism: a base, blades and twist ring, for a lamp shutter, a camera-style ornament or a fidget toy.

Four pegs and four flat test blades with holes at four clearances. Print it first to find the clearance your printer needs.

60 mm

Measure what goes in and add a few millimetres. The outside is much wider: the blades fold away under the ring.

45 mm

Straight depth of the inside. A tube splits it between its two halves.

70 %

How wide the open iris is, as a share of the inside diameter. A smaller opening keeps the lid narrower; the inside then narrows at 45° under the lid.

40 mm

How wide the iris opens. For a lamp, measure the bulb holder or shade ring it must clear.

6

More blades give a rounder opening but a taller stack and a shorter twist. Each blade adds one level.

Fit

0.30 mm

One gap for everything: pin to hole, pin to slot, blade to blade and ring to wall. 0.3 mm suits most printers; the fit test piece checks yours.

1.0 mm

Use a multiple of your layer height. Thicker blades are stiffer; thinner ones keep the lid low.

2.4 mm

Style

Outside shape
Twist ring grip

Engraved round the top of the ring. Short names print biggest.

Typeface
Mounting holes
3.4 mm

3.4 mm suits M3 screws. The holes sit in a flange round the base.

Colours and view

Every other blade in a second colour, for a striped iris. Print them as two batches.

Preview
60 %

Preview only: turns the ring to show the blades closed (0%) or fully open (100%).

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The method

    How the iris box works

    A camera iris closes with a ring of curved blades. Here each blade turns on a peg near the rim, and a pin hanging from the twist ring rides in a curved slot in the blade. Twist the ring and every blade swings in or out together.

    The blades are worked out for your opening: when open, each blade's inner edge sits just outside the opening, under the ring; when closed, the blades overlap to cover the whole middle. A real iris closes this way because every blade passes over the middle, so here each blade sits on its own level, a step higher than the one before, like a spiral staircase. No two blades share a level, so they cannot rub or catch. Each blade is also cut clear of the other blades' pegs and pins over the whole swing, so all the blades are the same.

    1. Size it: the inside diameter and depth you need, and how wide it opens.
    2. Print the fit test piece and set the clearance.
    3. Print the parts with no supports.
    4. Put it together in the order shown below the settings.

    Sizes

    How big the iris comes out

    Opening6 blades9 blades12 blades
    Ø20 mmØ71 mm ring, 19° twistØ79 mm, 11°Ø100 mm, 7°
    Ø30 mmØ92 mm, 21°Ø84 mm, 12°Ø99 mm, 7°
    Ø40 mmØ112 mm, 21°Ø104 mm, 14°Ø105 mm, 7°
    Ø50 mmØ133 mm, 22°Ø115 mm, 10°Ø111 mm, 8°
    Ø70 mmØ164 mm, 12°Ø146 mm, 10°Ø136 mm, 9°

    The blades need room to fold away, so the ring is two to four times as wide as the opening. Each blade adds a level (blade thickness plus clearance) to the height of the lid. Your exact sizes show in the readout.

    Options

    What each setting does

    SettingRangeGood to know
    Inside diameter and depth20–160 mm, 10–200 mmThe space inside the box, measured from what goes in.
    Opening50–100% of the insideNarrower openings keep the lid smaller. The inside narrows at 45° under the lid, so it prints without supports.
    Blades5 to 12More blades: a rounder opening, a taller lid and a shorter twist.
    Clearance0.15–0.6 mmOne gap for every moving fit. Find yours with the fit test piece.
    Blade thickness0.6–1.6 mmA multiple of your layer height. 1 mm is five 0.2 mm layers.
    Outside shapeRound, hexagon, one side per bladeThe twist ring stays round.
    GripRidges, a tab, both or plainThe ring has an end stop either way, so it cannot turn too far.

    Printing

    Printing and assembly tips

    • No supports. The body prints upright, the twist ring upside down (its top on the bed) and the blades flat. Every overhang is 45° or less.
    • Fit first. Print the fit test piece. Use the tightest test blade that still turns freely on its peg.
    • First layer. A squashed first layer narrows holes and slots. Elephant foot compensation in your slicer helps; so does a slightly higher clearance.
    • Blades: two or more perimeters, and keep them flat while they cool. A smooth bed gives smooth blades that slide well.
    • Two-colour name: the name is engraved into the face that prints on the bed. Change filament after the first layers for a contrasting name.
    • Assembly: blades go on with every blade closed, starting on the peg with no collar. Then the ring goes on and clicks over the groove.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits.

    Will it fit my printer?

    Choose your printer below the preview. The parts are packed onto as many plates as your bed needs. The body and the ring are the biggest parts, and the readout shows their size.

    Why is the lid so much wider than the box?

    The blades have to fold away somewhere when the iris is open. They tuck under the ring, so the ring is two to four times as wide as the opening. Make the opening a little smaller than the inside to keep the lid narrower.

    Can it print in place, already assembled?

    Not this design. Every blade sits on its own level, and printing them stacked would need supports under each one. The parts are quick to put together in the order shown.

    Can I sell what I print?

    The designs you make are yours, and the iris is a traditional mechanism anyone may make. The typefaces are open-licensed, which allows making physical products. It has small parts, so check toy-safety rules before selling for children.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-13. Community posts are one maker's experience, not a specification.

    1. Diaphragm (optics): iris diaphragms with movable blades Wikipedia
    2. Elephant foot compensation Prusa Research
    3. Color change Prusa Research
    4. SIL Open Font License SIL International