Free generator · Runs in your browser

Acoustic diffuser generator Real well depths, printed.

Make quadratic residue, primitive root and 2D skyline diffusers with depths worked out from your design frequency, or decorative 3D wall panels. Every panel splits into tiles that fit your printer, with tongues that line them up and keyhole or French cleat mounting.

  • Private by designNothing leaves this device
  • Schroeder mathsDepths from λ0 / 2N
  • No supportsTiles print on their backs
  • Ready to sliceOne file per plate

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Panel

Panel type
Diffuser
Skyline sequence

The sequence repeats every N wells (N − 1 for primitive root). A larger N gives more wells per period and a wider panel.

A primitive root skyline with N = 13 is a 12 × 12 grid of blocks; a quadratic residue one with N = 7 is 7 × 7.

Pattern
60 mm
15 mm
600 mm
400 mm

Tuning

Set the depth by
500 Hz

Wells are multiples of λ0 / 2N deep, where λ0 is the wavelength at this frequency. Lower frequencies need deeper wells.

150 mm

The readout shows the design frequency this depth gives.

3500 Hz

Sets the well (or block) width: about half a wavelength, 343 / (2 × frequency).

3.0 mm
1

Repeat the sequence to make a wider panel.

600 mm

The wells run from top to bottom.

Decorative panels have no tuning. They scatter some sound, but they are not designed to a frequency.

Tiles and mounting

9.0 mm

Keyhole slots need at least 9 mm and tongues at least 4.5 mm; thinner settings are raised to that.

220 mm

Used when no printer is picked. Pick your printer below the preview and the tiles fit its bed instead.

Each tile has tongues on its right and top edges, on the back, that drop into notches on the next tile.

Mounting

Measure your screw. The slot is 0.8 mm wider than the head.

Measure the screw’s thread. Sets the slot width and the cleat’s screw holes.

Colours

Preview

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The method

    How to make a printed diffuser

    A Schroeder diffuser is a row of wells of different depths. Sound reflected from the bottoms of the wells comes back with different delays, so it spreads out instead of bouncing back like a mirror. Diffusers scatter sound; they are not absorbers, and they do not soundproof a room.

    1. Pick the diffuser: quadratic residue or primitive root wells in one direction, or a 2D skyline of blocks.
    2. Set the design frequency (or the deepest well you can print) and the upper frequency.
    3. Pick your printer below the preview. The panel splits into tiles that fit its bed.
    4. Download, print every tile, push the tongues into the notches and hang it.

    The maths

    Well depths, widths and frequencies

    For a quadratic residue diffuser with N wells (N prime), well n has the sequence value sn = n² mod N and the depth dn = sn × λ0 / 2N. λ0 = c / f0 is the wavelength at the design frequency f0, with c = 343 m/s, the speed of sound in air at 20 °C. A primitive root diffuser uses sn = gⁿ mod N instead, with g a primitive root of N. A 2D skyline adds two sequences: s(m, n) = (sm + sn) mod N.

    The well width sets the upper limit: about half a wavelength, so w ≈ c / (2 × upper frequency). Fins between the wells keep each well separate.

    SequenceValues snDeepest well
    QRD, N = 70 1 4 2 2 4 14 × λ0 / 14
    QRD, N = 130 1 4 9 3 12 10 10 12 3 9 4 112 × λ0 / 26

    Example: N = 7 at 500 Hz gives λ0 = 686 mm, a depth unit of 49 mm and a deepest well of 4 × 49 = 196 mm. Choose “Deepest well” to set a depth your printer can reach; the readout then shows the design frequency it gives.

    Options

    Panels and patterns

    PanelWhat it isPrint height
    Quadratic residue, 1DWells between fins, deepest well from f0Up to the deepest well plus the back
    Primitive root, 1DN − 1 wells per period, no zero-depth wellSimilar to QRD
    2D skylineA grid of blocks, heights from the sequenceThe tallest block plus the back
    Hexagons, waves, pyramids, ribs, cellsDecorative relief; no tuningRelief depth plus the back

    Printing

    Printing and hanging tips

    • Orientation: each tile prints on its back, with wells or blocks up and no supports.
    • Weight and stiffness: a printed tile is hollow inside unless you raise the infill. The theory assumes hard, rigid wells, so use more walls and dense infill for an acoustic panel. The filament readout is for a solid print, so a sparse print uses far less.
    • Tongues: hang the first tile, then lower the next onto its tongues. A drop of glue makes the panel one piece.
    • Keyhole slots: two screws per tile, heads left out about 4 mm. Slide the tile down onto them.
    • French cleat: screw the wall cleat level, glue the panel cleat to the back near the top of the tile and the spacer near the bottom, then lift the tile onto the cleat.
    • Tall prints: check the height readout against your printer. Raise the design frequency or set a shallower deepest well if it is too tall.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits.

    Will it fit my printer?

    Choose your printer below the preview and the panel splits into tiles that fit its bed. The height of a tile is the deepest well plus the back, so check that your printer is tall enough.

    Will it fix my room’s sound?

    We can’t promise that. How well a diffuser works depends on the room, where it hangs, how far you sit from it and what else is in the room. The depths follow the published formulas, but a printed panel is not a tested product.

    Can I sell panels I print?

    The designs you make are yours, and the sequences are published mathematics anyone may use. Don’t claim acoustic performance you have not measured.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-12. Community posts are one maker's experience, not a specification.

    1. Diffuse sound reflection by maximum-length sequences (M. R. Schroeder, J. Acoust. Soc. Am. 57, 149, 1975) Acoustical Society of America
    2. Acoustic Absorbers and Diffusers: Theory, Design and Application (T. J. Cox and P. D’Antonio) CRC Press / Routledge
    3. QRD technical reference: well depths, design depth and well width subwoofer-builder.com
    4. Diffuser (acoustics) Wikipedia
    5. Speed of sound (about 343 m/s in air at 20 °C) Wikipedia