Free tool · Runs in your browser

Bed mesh visualizer Paste the numbers, see the bed.

Paste the bed mesh your printer reports and see it as a 3D surface, a heat map and a table. It reads Klipper, Marlin, Prusa and RepRapFirmware output, measures tilt and warp, and estimates how far to turn each bed screw.

  • Paste and goEight formats, found for you
  • Three viewsSurface, heat map, table
  • Tilt or warpAnd what to do about it
  • PrivateNothing is uploaded
−0.125 mmBlue: lower0.000 mmGrey: zero+0.125 mmRed: higher

Drag the 3D view to turn it, or use the arrow keys when it has focus.

Bed mesh of 5 by 5 points. Heights run from −0.030 to +0.125 mm, a range of 0.155 mm. The highest point is at the front right (column 5, row 1); the lowest is at the centre (column 3, row 3). Tilt left to right: 0.030 mm (right side higher). Tilt front to back: 0.000 mm (level). Range 0.15 mm: fine with mesh levelling.

Verdict

Range 0.15 mm: fine with mesh levelling

The whole range is less than one 0.2 mm first layer, so mesh levelling can follow it without trouble.

A rule of thumb, not a specification. How it is worked out.

Lowest
−0.030 mm
Highest
+0.125 mm
Range
0.155 mm
Mean
+0.040 mm
Std deviation
0.043 mm
Points
5 × 5
Tilt, left to right
0.030 mmright side higher
Tilt, front to back
0.000 mmlevel
Warp after removing tilt
0.140 mm0.041 mm RMS
Highest point
+0.125 mmfront right (column 5, row 1)
Lowest point
−0.030 mmcentre (column 3, row 3)
Bed heights in millimetres: 5 columns from left to right, 5 rows. The top row is the back of the bed.
1 left2345 right
5 back+0.095+0.050+0.040+0.065+0.125
4+0.043−0.003−0.013+0.013+0.072
3+0.025−0.020−0.030−0.005+0.055
2+0.043−0.003−0.013+0.013+0.072
1 front+0.095+0.050+0.040+0.065+0.125

Your mesh

Paste the printer’s reply as it is. “Recv:”, “//” and timestamps are removed for you.

Showing a sample: Klipper console output, 5 × 5 points.

Use this if the drawing is back to front compared with your bed.

View

×200

Heights are stretched so you can see them. A real bed this uneven would look flat.

Automatic uses zero when the mesh has points above and below it, and the mean otherwise.

The verdict compares the range with this.

Bed screws

For beds levelled by hand with three or four screws.

Compare two meshes

The first mesh is “before”, this one is “after”. The difference is after minus before.

Save or share

The link holds the mesh itself, so anyone who opens it sees the same view. The STL is the exaggerated surface as a solid block.

Your mesh is read on this device and is never uploaded.

Advertisement

Step by step

How to get your bed mesh as text

Every firmware can print its mesh to the console. Send the command from your printer’s web interface or a serial terminal, copy the reply and paste it above.

FirmwareMeasurePrint the meshWhat to copy
KlipperBED_MESH_CALIBRATEBED_MESH_OUTPUTEverything from “Mesh Leveling Probed Z positions” down. The probed points are used; the interpolated “Measured points” are ignored.
Klipper, saved meshBED_MESH_PROFILE SAVE=default then SAVE_CONFIGOpen printer.cfgThe [bed_mesh default] block at the end of the file, with its points = rows and min_x to max_y lines.
Marlin, bilinear or mesh bed levellingG29M420 VThe “Bilinear Leveling Grid” or “Measured points” table, with or without its row and column numbers.
Marlin, UBLG29 P1G29 T or M420 VThe “Bed Topography Report”, including the corner coordinates above and below the map. The comma-separated map from G29 T1 also works.
Prusa firmware (MK3 family)G80G81“Measured points” and the rows under it. On other models, try M420 V.
RepRapFirmwareG29Download heightmap.csvThe whole file, from the system files in the web interface.
Anything elseRows of numbers separated by spaces, commas or tabs, one row of the bed per line.

Heat the bed to printing temperature and let it soak for a few minutes before you measure. Beds change shape as they warm up.

Reading it

How to read a bed mesh

  • Each number is a height in millimetres. A positive number means the bed is higher at that point than the printer’s zero; a negative number means it is lower.
  • Red is high, blue is low, grey is the middle. Every cell also shows its value, so you never need to rely on the colours.
  • Range is the highest point minus the lowest. It is the number most people quote.
  • Standard deviation shows how far a typical point is from the mean. One bad corner raises the range a lot but the deviation only a little.
  • Tilt is the part of the range that a flat but sloping bed would give. It comes from a best-fit plane through all the points, and it is what bed screws or independent Z motors remove.
  • Warp is what is left after the tilt is taken away: the bow, dish or twist of the bed itself. Only mesh levelling, shims or a flatter plate deal with it.

The 3D view stretches heights by the Z exaggeration, or a real bed would look perfectly flat. At ×100, a 0.1 mm bump is drawn 10 mm tall.

Rules of thumb

How the verdict is worked out

There is no official limit for a “good” mesh. The verdict uses these rules of thumb, in this order:

VerdictRuleWhy
Very flatRange of 0.05 mm or lessKlipper’s probe guide treats a probe that repeats worse than 0.025 mm as too inaccurate for levelling. Twice that is about the smallest difference worth reading.
Tilt dominatesTilt of at least 0.1 mm (or half a first layer, if larger) and more tilt than warpTilt can be removed at the hardware, so do that before asking the mesh to follow it. Klipper’s screw tool calls a bed level once every screw needs less than 6 minutes of a turn, which is 0.05 mm on an M3 thread.
Fine with mesh levellingRange no more than one first layer (0.2 mm unless you change it)Klipper’s bed mesh guide uses one layer height as the point where a mesh’s variation needs caution.
Usable, but worth improvingRange up to 2.5 first layersThe printer can follow it, but the first layers are stretched and squeezed to do so.
Too much for mesh levelling aloneRange over 2.5 first layersKlipper’s guide notes that software correction only approximates the bed’s shape and cannot make up for mechanical problems.

Treat these as a starting point. A large, thin bed will never be as flat as a small cast plate, and a 0.3 mm first layer forgives more than a 0.12 mm one.

Levelling by hand

How the screw estimate works

The tool fits a flat plane through the whole mesh and reads its height at each screw. The difference from the screw you leave alone, divided by the thread pitch, is the number of turns.

ThreadPitch (height per full turn)A quarter turn moves the bed
M30.5 mm0.125 mm
M40.7 mm0.175 mm
M50.8 mm0.200 mm
  • It is an estimate. Springs, silicone spacers and a bed that flexes all change the result. Turn the screws, measure a new mesh and repeat.
  • Measure the screw positions on your own bed. The starting values are only placeholders.
  • If your mesh has no coordinates, the tool assumes it covers the whole bed. Meshes from a saved Klipper profile, UBL and RepRapFirmware carry their own coordinates.
  • Direction: on most beds, turning a knob clockwise (seen from above) raises the bed and closes the gap to the nozzle. Check yours on one screw.
  • No screws? Printers with a fixed bed or several Z motors level themselves; use the tilt figures to check that they did.

Formats

What the tool recognises

FormatRecognised byFirst row is
Klipper console output“Mesh Leveling Probed Z positions”The front of the bed
Klipper saved meshA points = lineThe front
Marlin bilinear grid“Bilinear Leveling Grid”, or numbered rows and columnsThe front (row 0)
Marlin mesh bed levelling“Measured points” with numbered rowsThe front (row 0)
Marlin UBL“Bed Topography Report” or corner coordinates in bracketsThe back
Prusa G81“Measured points” without row numbersThe back
RepRapFirmware heightmap.csv“RepRapFirmware height map” or its column namesThe front
Plain gridRows with the same count of numbersTaken as the front

If the drawing is back to front compared with your bed, switch on “Flip front and back”. The numbers and statistics stay the same.

Questions, answered

Is my mesh uploaded?

No. The text is read and drawn in your browser. A share link carries the mesh inside the link itself, after the # sign, which browsers do not send to a server.

What is a good bed mesh range?

There is no official figure. As a rule of thumb, a range under one first layer (often 0.2 mm) is comfortable for mesh levelling, and under 0.05 mm is about as flat as a probe can measure.

Does mesh levelling fix a tilted bed?

It can follow a small tilt, but it is better to remove tilt at the hardware first. A mesh that follows a slope shifts every layer slightly, and it leaves less room to correct the real warp.

Why is my mesh different every time?

Heat and the probe. A bed changes shape as it warms, so measure at printing temperature after a few minutes of soaking. Differences of 0.02 to 0.03 mm between runs are within what many probes repeat.

The view is mirrored. What do I do?

Switch on “Flip front and back” or “Flip left and right”. Some firmware prints the back row first and some the front; the tool follows each firmware’s own order, but a plain grid cannot say which way round it is.

Can I print the surface?

Yes. “STL surface” saves the exaggerated surface as a solid, closed block with a flat base, at the mesh’s real width and depth when the mesh includes coordinates.

Is it free?

Yes. There is no account and no limit.

Sources

Print advice is a starting point drawn from these references, checked on 2026-11-11. Community posts are one maker's experience, not a specification.

  1. Bed Mesh Klipper documentation
  2. Probe calibration (probe repeatability) Klipper documentation
  3. Bed leveling: adjusting bed screws and screw tilt Klipper documentation
  4. Configuration reference: screws_tilt_adjust Klipper documentation
  5. M420 – Bed Leveling State Marlin
  6. G29 – Bed Leveling (Unified) Marlin
  7. Prusa firmware-specific G-code commands (G80, G81) Prusa Research
  8. G-code dictionary: G29 mesh bed probe Duet3D
  9. ISO 261: ISO general purpose metric screw threads, general plan ISO