Free generator · Runs in your browser

Colour lithophane generator Backlit photos in colour.

Turn a photo into a colour lithophane: a white lithophane with thin cyan, magenta and yellow layers on top that show the picture in colour when lit. Use your own filaments, tune them with a calibration card, and download a 3MF with one object per filament. Experimental.

  • Private by designPhotos stay on this device
  • Your filamentsSet each colour and TD
  • Calibration cardTune the colours first
  • Ready to sliceOne object per filament

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Photo or card

Make

Print this first. A card of patches with known thicknesses of each filament. Hold it up to a light and compare it with the preview here, then adjust each filament’s TD until they match.

Crop and adjust

1.00

1 fits as much of the photo as the panel’s shape allows.

0.50
0.50
0.00
1.00
1.20

Thin colour layers look paler than a screen, so a little extra saturation helps.

1.00

Above 1 lifts the shadows; below 1 deepens them.

The card has no photo to adjust. Its patch thicknesses follow the thickness limits under Layers and detail.

Shape and size

Shape
120 °

How far the panel wraps round. A curved panel prints standing up.

100 mm
75 mm

The photo is cropped to this shape; zoom and centre choose the part shown.

A rim of white at the thickest setting, which stiffens the panel and frames the picture.

3.0 mm

A separate block with a slot that holds the panel upright, leaning back 15°.

The card is 88 × 58 mm: 8 patches of 10 mm in five rows, with a solid 4 mm rim.

Filaments

Filament set

The standard set uses translucent cyan, magenta and yellow over white. With your own four, filament 1 is the base and each of the others works on the colour of light it blocks most.

TD (transmission distance) is how many millimetres of a filament it takes to block light. It differs between brands and colours, so the values here are only a start: print the calibration card and adjust them.

Filament 1 · White basethe base (lightest)
Filament 2 · Cyana colour layer
Filament 3 · Magentaa colour layer
Filament 4 · Yellowa colour layer

Layers and detail

Every thickness is a whole number of these layers. Slice with exactly this height; 0.08 or 0.1 mm suits colour lithophanes.

Pixels are never smaller than the nozzle, which cannot print finer detail.

0.40 mm

Grid spacing in the download. Large panels are made coarser if they would pass 1.5 million triangles.

0.60 mm

The brightest parts of the picture.

3.00 mm

The darkest parts, and the border.

0.00 mm

0 leaves out a colour where the picture has none.

1.20 mm

The strongest colour. Very see-through filaments need more.

Preview

Lit colours paints the top with the colours the model predicts when the panel is lit from behind. Filament parts shows the four parts as they print; where a colour is not needed its part is only a film thinner than a layer, which the slicer skips.

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The method

    How to make a colour lithophane

    A normal lithophane is one white filament: thick where the photo is dark, thin where it is bright. A colour lithophane adds three thin, see-through layers on top, in cyan, magenta and yellow. Lit from behind, each colour layer filters the light, and together they rebuild the photo’s colours.

    This tool is experimental. The colours depend on how see-through each of your filaments is, so the first print should be the calibration card.

    1. Enter your four filaments and their TD values, or keep the standard set.
    2. Print the calibration card, hold it up to a light and compare it with the preview. Adjust the TD values until they match.
    3. Add your photo, crop it and set the size.
    4. Download the 3MF and print it on a multi-material printer, each part with its own filament.

    How it works

    From a photo to four layers

    Each pixel gets a thickness of each filament:

    • Colour: the photo is split into cyan, magenta and yellow, the way a printer splits ink. Cyan blocks red light, magenta blocks green and yellow blocks blue. The more a pixel needs a colour, the thicker that layer is, up to the thickest colour layer you set.
    • Thickness from TD: light through a filament fades away with thickness and is down to about 5% at its TD (the Beer–Lambert law). A very see-through filament needs a thicker layer for the same colour.
    • Brightness: the white base is then made thick enough that the lit pixel is as bright as the photo, from the thinnest white for bright areas to the thickest for dark ones.
    • Whole layers: every thickness is snapped to the layer height and kept between the thinnest and thickest you set.

    The parts stack: white at the bottom, then cyan, magenta and yellow. Each is its own object in the 3MF, so a multi-material printer prints all four together. The model ignores light scattering and the way real filaments mix, which is why the card matters.

    Calibration

    Print the calibration card first

    Choose Calibration card and print it with the same filaments, layer height and settings you will use for the photo. Seen from the top, it has five rows:

    RowPatches, left to right
    1 · WhiteThe white base in 8 steps from the thinnest to the thickest
    2 · Filament 2 (cyan)8 steps of colour over the thinnest white
    3 · Filament 3 (magenta)8 steps of colour over the thinnest white
    4 · Filament 4 (yellow)8 steps of colour over the thinnest white
    5 · Mixes2 + 3, 2 + 4, 3 + 4 and all three, each at the thickest colour layer

    Tune it by eye: hold the card in front of a bright, even light (a window or a white screen) next to the preview here with Lit colours on. If a row looks deeper in real life than on screen, lower that filament’s TD; if it looks paler, raise it. If the white row looks darker than the preview, lower the white TD. The exact thickness of each patch is listed under the preview.

    The mixes row checks how the colours combine: cyan with magenta should look blue, cyan with yellow green, and magenta with yellow red.

    TD values

    Starting values

    The standard set starts from one filament maker’s published values for its translucent cyan, magenta and yellow and its white. Other brands differ, sometimes a lot. Using four filaments from one brand and product line helps the colours match.

    FilamentColourTD
    White base #EBF7FF3.2 mm
    Cyan #08ABFB8 mm
    Magenta #D93B907.8 mm
    Yellow #F9ED3D14 mm

    Options

    Sizes and options

    OptionRangeNotes
    Size30–250 mm each sideThe photo is cropped to the shape
    ShapeFlat or curved (30–180°)Curved panels print standing up
    Layer height0.04–0.2 mm0.08 or 0.1 mm suits colour lithophanes
    Pixel size0.2–1.5 mmNever finer than the nozzle
    White base0.4–6 mmThinnest for bright areas, thickest for dark ones and the border
    Colour layers0–3 mm eachThinnest where a colour is not needed, thickest for full colour
    File sizeUp to 1.5 million trianglesLarge panels get a coarser grid

    Printing

    Printing tips

    • Multi-material printer: open the 3MF, keep the four parts together as one object and give each part its filament. The readout estimates how many filament changes the print needs; on one nozzle with manual swaps that is far too many.
    • Print flat, white side down, with no supports. Slice at exactly the layer height you chose.
    • 100% infill so light passes through even, solid plastic and no infill pattern shows.
    • Purge well when changing to a lighter filament, or traces of the darker one tint it.
    • Curved panels print standing, so the colour layers become thin walls. Walls thinner than about one nozzle width may be left out by the slicer: flat panels give the most reliable colour.
    • Light it evenly from behind with a white light. The colours change with the light’s colour and distance.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits, and your photo never leaves this device.

    Will it fit my printer?

    Choose your printer below the preview to check. If it is too big, lower the width or height; the stand prints beside the panel.

    Can I sell prints I make with it?

    The models you make are yours. The photo is the part to check: only use photos you took, bought a licence for, or have permission to use.

    Why is it marked experimental?

    The colours come from a simple model of how light passes through each filament. Real filaments scatter light, vary between spools and mix in ways the model does not capture, so the first print may be off. The calibration card is there to bring your TD values close to your filaments.

    Do I need a multi-material printer?

    In practice, yes. The four filaments change many times within each layer. A printer with an automatic filament changer or several tool heads handles that; swapping by hand is not practical.

    Why do my colours look pale?

    Thin colour layers only filter part of the light. Raise Colour layer, thickest, add saturation, or use a stronger light. If one colour is paler than the preview, lower its TD.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-12. Community posts are one maker's experience, not a specification.

    1. The mechanics of multi-material color lithophane printing QIDI Tech blog
    2. HEX codes and transmission distances Polymaker wiki
    3. Beer–Lambert law Wikipedia