Free generator · Runs in your browser

Temperature tower generator Tune it in.

Make a temperature tower, retraction tower or flow, overhang, bridge, size or first-layer test, sized to your nozzle and layer height, with a table of exactly where each change goes and the steps for your slicer.

  • Free and privateNothing to upload
  • Six testsTowers, tiles, arms and squares
  • Exact layersChanges land on block edges
  • Ready to sliceSTL, 3MF and a change table

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Test

Calibration print
0.40 mm

Sets the cone tip, post and label sizes so they stay printable.

0.20 mm

Slice with exactly this layer height. Every block is a whole number of layers.

0.20 mm

Values

Fills the range from a filament maker’s published nozzle range. Check the range printed on your own spool.

230 °C
190 °C

Usually hottest at the bottom. Up to 14 blocks.

5 °C
10.0 mm

Rounded to whole layers.

Change
0.0 mm
2.0 mm

Direct drive extruders usually need 0–2 mm; long tube (Bowden) setups more.

0.2 mm
20 mm/s
60 mm/s
5 mm/s
5.0 mm
30 mm

The travel the nozzle makes over open air on every layer.

Flow test
90 %
110 %
5 %
30 mm
0.45 mm

The wall you measure should come out this thick.

Include
20 °
80 °

Measured from vertical: 0° is a straight wall, 90° flat.

10 °
10 mm
80 mm
10 mm
Shape
20 mm
100 mm
5.0 mm
Pattern
25 mm
15 mm

Pick your printer below the preview and the squares spread across its bed. Without one, they use the bed size here.

220 mm
220 mm

How to apply it

Your slicer
Printer firmware

Colours

Labels are their own object in the 3MF. On one nozzle, print everything in one colour.

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The method

    How to calibrate with a test print

    Each test changes one thing and keeps the rest the same, so the print shows the effect of that one setting. Towers change a setting as they grow; the other tests use your normal settings and show where the printer reaches its limit.

    1. Choose the test, your nozzle and the layer height you will slice with.
    2. Set the range. For a temperature tower, choose the material to fill in a maker’s published range, then check it against your spool.
    3. Download and slice at exactly the layer heights shown.
    4. Apply the changes. The change table gives each block’s height and layer, the G-code line, and the steps for your slicer.
    5. Read the print and enter the best value in your filament or printer profile.

    Order

    Which test first

    TestWhat it setsWhat to look at
    First layerZ offset and bed levellingLines that touch without gaps or ridges, on every square
    Temperature towerNozzle temperatureOverhangs, bridge, cone tip and strings on each block
    FlowFlow (extrusion multiplier)A closed, smooth top; or the wall thickness
    Retraction towerRetraction distance or speedThe shortest value with no strings between the posts
    Overhang and bridgeNothing: shows the limitsThe steepest clean arm and the longest flat bridge
    Dimensional accuracyHole compensation, shrinkageMeasured sizes against the nominal ones

    Start with the first layer, then temperature, since flow and retraction both depend on it.

    Exact layers

    Why block heights snap to layers

    A change made at a layer applies to the whole layer. If a block were 10 mm tall at a 0.28 mm layer height, its boundary would fall partway through a layer, and the slicer would round it one way or the other. Here every block is a whole number of layers, so its first layer starts exactly at the Z height in the table.

    Layers are counted from 1, and each layer’s Z is the height of its top: the first layer’s top is its height, and each next layer adds one layer height. Slicers show the same figure on the preview’s layer slider. Turn off variable or adaptive layer height for these prints.

    Starting ranges

    Nozzle ranges filament makers publish

    MaterialNozzle rangeSource
    PLA190–230 °CPolymaker PolyLite PLA
    PETG230–260 °CPolymaker PolyLite PETG
    ABS245–265 °CPolymaker PolyLite ABS
    ASA230–260 °CPolymaker ASA
    TPU 95A210–230 °CPolymaker PolyFlex TPU95
    PC250–270 °CPolymaker PolyLite PC
    Nylon250–270 °CPolymaker PolyMide CoPA

    These come from one maker’s published range. Brands differ, and the range on your spool is the one to trust. For the ranges other makers publish, see the filament drying chart.

    Printing

    Printing tips

    • No supports on any of these prints: the overhangs and bridges are the test.
    • One change at a time: keep speeds, cooling and flow the same while a tower runs.
    • Dry filament first. Damp filament strings and bubbles at any temperature, which hides the real result.
    • Retraction commands only work if your slicer uses firmware retraction. Otherwise use the table with your slicer’s own per-height settings.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits, and no G-code to upload: you apply the changes in your own slicer.

    Will it fit my printer?

    Choose your printer below the preview. The check updates as you change the number of blocks and their height; a tall tower at a small layer height can take several hours. The first-layer test uses your printer’s bed size to spread its squares.

    Why did nothing change between blocks?

    The temperature or retraction change was not added to the G-code. Open the sliced file’s preview at a block’s first layer and check for the command, or use the single line for the layer change G-code box.

    Can I sell prints made with it?

    The designs you make are yours. The label typeface is open-licensed. We make no claims beyond that.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-12. Community posts are one maker's experience, not a specification.

    1. Insert pause or custom G-code at layer Prusa Research
    2. Macros (placeholders and conditions) Prusa Research
    3. Built-in placeholders and variables OrcaSlicer wiki
    4. Temperature calibration OrcaSlicer wiki
    5. Retraction calibration OrcaSlicer wiki
    6. ChangeAtZ post-processing script UltiMaker Cura (GitHub)
    7. Using Cura: post-processing (Extensions menu) Mainsail documentation
    8. M104: Set Hotend Temperature Marlin Firmware
    9. M207: Set Firmware Retraction Marlin Firmware
    10. G-Codes (M104, SET_RETRACTION, G10 and G11) Klipper documentation
    11. G-code (M104 support by firmware) RepRap wiki
    12. Extrusion multiplier calibration Prusa Research
    13. Polymaker PolyLite PLA technical data Polymaker wiki
    14. Polymaker PolyLite PETG technical data Polymaker wiki