Free generator · Runs in your browser

Cryptex generator Locked by your own word.

Make a combination-lock tube that opens only when its rings spell your code. Size it for a note, a ring, cash or a gift card, choose the letters and style, and print every part without supports.

  • Private by designYour code never leaves this device
  • 3 to 8 ringsLetters, digits or symbols
  • No supportsEvery part prints as laid out
  • Ready to sliceEach part its own object

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Code

Make

A short sleeve, a short drawer with one pin and one blank ring. Print it first: the ring should turn and click, and the pin should pass the notch only when they line up.

3 to 8 characters: one ring each. The code stays in this browser and is left out of shared links.

On the rings
Letters on each ring

Fewer letters are bigger and easier to read on a small tube. A shorter set always includes the letters of your code.

Every ring carries these symbols in this order. The code may only use symbols from this set.

Off: a shared link carries the design but not your code. Turn it on only to send the whole solution.

Size

What goes inside

Ø20 × 60 mm inside: a rolled letter or a strip of paper up to 58 mm wide.

Ø26 × 14 mm inside, or longer if the rings need the room. Ring sizes vary: measure yours across its widest point and use Custom if it is bigger.

Ø22 × 80 mm inside: a roll of banknotes up to 77 mm wide, such as US dollars (66 mm) or euro notes.

Ø22 × 62 mm inside. USB sticks vary a lot: measure yours and use Custom if it does not fit.

Ø56 × 88 mm inside: a standard gift or payment card (85.6 × 54 mm) standing on end. A large print.

20 mm
60 mm

If the rings need more room than this, the inside comes out longer.

Turn off to set the ring width yourself. Spare length goes into a longer end cap.

9.0 mm
0.30 mm

The gap between every pair of sliding or turning surfaces. 0.3 mm suits most printers; print the fit test piece to check.

Style

Letters

The letters are separate parts that sit flush in the rings: give them their own filament on a multi-material printer.

Typeface
Rings
Ends

A small raised arrow on the handle and on the end cap. The code opens the tube when it sits between them.

Each ring comes in two pieces, so you can change the code after printing: open the tube, slide the lettered rings off, turn them and slide them back.

Engraved along the inner tube, so it shows only once the tube is open.

Colours and view

Preview

Turn off to see the rings scrambled, as someone else would find it.

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The method

    How a cryptex works

    A cryptex is a tube locked by a word. A drawer slides inside a slotted sleeve, and a row of pins on the drawer sticks out through the slot. Each lettered ring turns on the sleeve and has a flange that blocks its pin, with one notch cut under the code letter. Line every code letter up between the two arrows and all the notches meet the slot, so the drawer slides out.

    1. Type your code. Each character gets a ring.
    2. Pick a size for what goes inside.
    3. Print the fit test piece, then the parts.
    4. Put it together in the order on the assembly sheet, and keep the sheet somewhere safe.

    Sizes

    What fits inside

    ForInsideWhy
    Rolled noteØ20 × 60 mmA rolled letter or paper strip up to 58 mm wide.
    RingØ26 × 14 mmRoom for most finger rings. Measure yours: sizes vary.
    Cash rollØ22 × 80 mmUS notes are 66.3 mm wide and today’s euro notes 62 to 77 mm.
    USB stickØ22 × 62 mmA typical stick. Measure yours: there is no standard size.
    Gift cardØ56 × 88 mmA standard ID-1 card is 85.60 × 53.98 mm.
    CustomØ10–70 × 10–180 mmMeasure the gift and add 2 mm all round.

    The tube is about 20 mm wider than its inside, or about 25 mm with re-codable rings. With all 26 letters on a small tube the letters get small: under 3 mm tall the generator suggests a set of 13 or 10.

    Options

    Letters, rings and ends

    OptionChoicesGood to know
    LettersEngraved, raised or two-colour inlayEngraved prints cleanest. Inlay needs a multi-material printer.
    On the ringsA to Z, 13 or 10 letters, digits, your own symbolsA code of 5 letters from 26 has 11,881,376 combinations; 4 digits have 10,000.
    RingsPlain, knurled rims or flutedKnurled rims stand a little proud and protect the letters.
    EndsDome, flat or crownAll three sit flat on the bed.
    Re-codableLettered rings on splined key ringsChange the code any time the tube is open.

    Printing

    Printing and assembly tips

    • No supports. Rings print flat with the flange down, the sleeve and drawer stand upright, and the end cap prints open side up. The pins have a 45° underside. The crown style has short bridges between its blocks.
    • Fit first. Print the fit test piece and adjust the clearance until the ring turns freely and clicks.
    • Click arms. Each ring has two thin arms in its first layers. If a squashed first layer fuses them, free them with a thin blade.
    • A brim helps the tall drawer and sleeve stay on the bed.
    • End cap. It pushes onto the sleeve with its rib in the slot. Add a drop of glue once you are happy with the fit.
    • It is a puzzle, not a safe. A printed lock keeps a gift a surprise; it will not stop someone determined.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits.

    Will it fit my printer?

    Choose your printer below the preview. The parts are packed onto as many plates as your bed needs, and the readout shows the tallest part. The gift card size is the largest: its drawer stands about 100 mm tall.

    Is my code private?

    Yes. Everything is built in your browser and nothing is uploaded. The code is saved only in this browser, and a shared link leaves it out unless you turn on “Include the code in shared links”. The files themselves do reveal the code to anyone who studies the notches.

    Can I change the code later?

    With re-codable rings, yes: open the tube, slide the lettered rings off, turn each to a new letter over the notch and slide them back. Standard rings have the code built in.

    Can I sell ones I print?

    The designs you make are yours, and the combination-lock tube is a traditional puzzle anyone may make. The typefaces are open-licensed, which allows making physical products. It has small parts, so check toy-safety rules before selling for children.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-13. Community posts are one maker's experience, not a specification.

    1. ISO/IEC 7810: identification card sizes (ID-1, 85.60 × 53.98 mm) Wikipedia
    2. Currency FAQ: size of paper money (2.61 × 6.14 inches) US Department of the Treasury (archived)
    3. Euro banknotes: sizes Oesterreichische Nationalbank
    4. SIL Open Font License SIL International