The method
Turn a picture into a charm
Add a drawing, sticker, logo or photo. The picture is traced on your device, grouped into a few filament colours and built into a flat charm: a base in one colour with each picture colour as its own part on top. Then pick what the charm is for, and the back changes to suit.
- Add a picture. Transparent PNGs and flat-colour art give the cleanest charms.
- Pick the charm type and measure anything it has to fit: a straw, a pencil or a bag hole.
- Choose how colours print: stepped for one nozzle, raised or flush for a multi-material printer.
- Download and print flat, picture up, with no supports.
Charm types
Nine charms from one picture
| Type | The back | Measure |
|---|---|---|
| Badge reel topper | Flat, to glue on | Nothing |
| Straw topper | A channel through the charm | Your straw’s diameter |
| Fridge magnet | A pocket for a disc magnet | Your magnet (pick its size) |
| Earrings | A mirrored pair with small loops | Your ear wires or jump rings |
| Key ring and nail saver | A loop, and a thin lever tab for can ring-pulls | Nothing |
| Hair-tie holder | Notches on both sides | A hair tie’s thickness |
| Pencil topper | A socket for the pencil’s end | The pencil, across its corners |
| Zipper pull | A loop for a jump ring or cord | Nothing |
| Bag charm | A push-in peg for rubber tote bags | The bag’s hole and wall |
Sizes of straws, pencils and bag holes vary between brands, so the generator asks for your measurement instead of guessing.
Colour
Colours on one nozzle, or many
| Style | Looks like | Printer |
|---|---|---|
| Stepped | Each colour a step higher than the one before | Any printer: a colour change at each height the page lists |
| Raised | All colours at one height on the base | Multi-material (AMS, MMU, tool changer) |
| Flush | A smooth top with colours inlaid | Multi-material |
On one nozzle, add a filament change in your slicer at the first layer at or above each height in the advice. The printer pauses, you swap filament, and every area at that step prints in the new colour. Areas close to the base colour print as part of the base.
Printing
Printing tips
- Small details: a 0.4 mm nozzle draws lines about 0.4–0.45 mm wide, so features under about 0.8 mm (two lines) may not print. The generator merges thinner areas into their neighbours; the advice says how much.
- Channels and pockets print without supports: the straw channel has a pointed roof that ends in a short bridge.
- Glue: superglue holds PLA to badge reels, magnets and the bag peg.
- Material: PLA is fine for most charms; PETG copes better with hot cars and dishwater-warm drinks.
Questions, answered
Is it free to use?
Yes. No account, no watermark, no limits, and your picture never leaves this device.
Will it fit my printer?
Charms are small, so almost any printer fits one. With copies, choose your printer below the preview and they fill its plates; with more than one plate you get one file per plate.
Can I sell charms I print?
The charm designs you make are yours. The picture is the part to check: only use art you drew, bought a licence for, or have permission to use. Characters and logos are usually trademarked or copyrighted. Charms are small parts, so check toy-safety rules before selling them for children.
Why does my photo look blotchy?
Photos have gradients, which become bands of colour. Lower the number of colours, raise Smoothing, or use a flat-colour drawing of the photo.
Can I use an SVG?
Yes. Your browser draws the SVG, then it is traced like any picture, so gradients and effects in the SVG show up as they look on screen.
Sources
Print advice is a starting point drawn from these references, checked on 2026-11-10. Community posts are one maker's experience, not a specification.
- Color change Prusa Research
- View slicing information (pauses and filament changes) Bambu Lab
- Modeling with 3D printing in mind Prusa Research
- Multicolor printing with a Prusa: beginner’s guide Prusa Research
- Magnets safety education center U.S. Consumer Product Safety Commission