Free generator · Runs in your browser

Drawer storage tower generator A drawer for every part.

Make a swing-out drawer tower, stacking drawer units or a parts cabinet, with every drawer sized to what it holds, divided, labelled and split to fit your printer.

  • Private by designNothing leaves this device
  • Three kindsSwing-out, stacking, cabinet
  • No supportsDrawers print open side up
  • Ready to sliceFits your bed, plate by plate

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Tower

Kind of tower
12
Drawer shape
Rod

Measure your rod or dowel with calipers: sizes sold as “8 mm” or “1/4 inch” are often slightly off.

10 mm
0.50 mm

Added to the rod to make each drawer’s bore, so drawers turn freely.

3

Every unit has its own frame. Print more later and stack them on top.

Drawers per unit
4
4

Drawer insides

Size the drawers

Measure the biggest thing that goes in one drawer, or the space you want. On wedge drawers the width is at the front.

Battery and card sizes are the published nominal sizes. Beads, screws and bricks vary, so measure one.

Items sit
1.0 mm

Added on every side and on top, so they lift out easily.

0
Dividers run

Details

Pull
Front label

Measure the card or label strip you will use. A window too big for the front is shrunk to fit.

Paper is about 0.1 mm, card about 0.3 mm. The slot is 0.4 mm thicker.

Drawer 1 takes the first label, drawer 2 the next. Short labels stay readable.

Typeface
0.8 mm

A small ramp on each drawer clicks past a lip at the front of its cell, so drawers don’t slide out by themselves.

0.30 mm

Gap between each drawer and its cell, per side, and around the stacking pegs.

Base

Wall mount adds keyhole ears for two screws (stacking units and cabinets). A swing-out tower always stands on its base; plain gives it screw holes instead of feet.

A tray on top for things you reach for often.

20 mm

Colours

Each drawer takes the next of six colours, each its own part.

Preview

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The method

    How to make a drawer storage tower

    Pick a kind of tower, size one drawer from what it holds, add labels and a base, and the generator builds every frame, drawer and tray, then lays them out on your printer’s plates.

    1. Pick a kind: a swing-out tower, stacking units or a cabinet.
    2. Size the drawers: type a measured inside size, or say how many items each drawer holds.
    3. Add details: dividers, a pull, a label window or raised text, feet or a wall mount, a top tray.
    4. Choose your printer below the preview, so big frames and long rods split into pieces that fit.
    5. Download and print. Frames lie on their back and drawers print open side up, with no supports.

    Kinds

    The three kinds of tower

    KindHow it worksGood for
    Swing-out tower6–20 wedge or rectangular drawers stacked on a rod. Each turns out on its own pivot and clicks shutScrews, nuts and washers on a workbench
    Stacking unitsUnits of 1–4 drawers, each with its own frame; pegs at the back line them upBead and craft storage that grows over time
    Parts cabinetA grid of up to 8 × 8 drawers in one frame, split into pieces for your bedElectronics parts, with a label on every drawer

    Sizes

    Item sizes the helper uses

    The “to hold a number of items” helper uses these published nominal sizes. Real items vary a little, so the helper adds the room you choose around them. For anything else, choose Something I measured.

    ItemSize usedSource
    AA cell14.5 mm across × 50.5 mmList of battery sizes
    AAA cell10.5 mm across × 44.5 mmList of battery sizes
    9 V battery48.5 × 26.5 × 17.5 mmList of battery sizes
    20 mm coin cell20 mm across × 3.2 mmList of battery sizes
    Full-size memory card32 × 24 × 2.1 mmSD card
    Micro memory card15 × 11 × 1 mmSD card

    Fit

    Clearances and the tolerance test

    Printers differ, so the gap a drawer needs differs too. Lab guides for desktop printers suggest starting around 0.2–0.4 mm per side for sliding parts. The defaults are 0.3 mm round each drawer and 0.5 mm of play on the swing-out pivot.

    • Drawers stick: raise Fit clearance by 0.05–0.1 mm.
    • Swing drawers bind on the rod: raise Pivot clearance, or check the rod with calipers.
    • Not sure: print a tolerance test first.

    Printing

    Printing tips

    • No supports: drawers print open side up and frames lie on their back. Knobs are teardrops and label ledges have 45° undersides.
    • Printed rods lie on a small flat. A long rod comes in pieces joined by pegs; glue them.
    • Metal rods and dowels are stiffer for tall towers. Cut to the length the advice gives.
    • Big cabinets split into frame pieces with their own walls; glue them edge to edge.
    • Colours: the frame, the drawers (or each rainbow colour) and raised labels are separate parts in the 3MF.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits.

    Will it fit my printer?

    Choose your printer below the preview. Cabinet frames and printed rods split into pieces that fit its bed, and the drawers spread over as many plates as needed. Stacking units are printed whole, so the advice warns if one is too big.

    Can I sell towers I print?

    The designs you make are yours. The typefaces are open-licensed, which allows making physical products. Drawers hold small parts, so think about who will use them before selling.

    How tall can a swing-out tower be?

    Up to 20 drawers. A tall tower with many drawers swung out to one side can tip, so open a few at a time, use a metal rod, or fix the base down.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-12. Community posts are one maker's experience, not a specification.

    1. List of battery sizes Wikipedia
    2. SD card Wikipedia
    3. Design the clearance and tolerance UAL Creative Computing Institute
    4. SIL Open Font License SIL International