Free generator · Runs in your browser

Cosplay helmet size calculator Scale it once, print it right.

Find the scale a downloaded helmet or mask needs to fit your head. Type its inside sizes or load the STL to measure it at eye level, then check it fits your printer and print a test ring before the whole helmet.

  • Private by designYour model never leaves this device
  • Measured, not guessedSliced at eye level
  • Test before you printA ring at the scaled inside
  • Slicer readyCopy the scale numbers

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Your head

How to measure your head
  1. Around (circumference): a soft tape level round your forehead about 2 cm above the eyebrows, just above the ears and round the fullest part of the back of your head. Snug, not tight.
  2. Length: straight from the most forward point of your forehead, between the brows, to the farthest point at the back of your head. Use calipers, or two books against your head and a ruler between them.
  3. Width: the widest straight distance across your head above and behind the ears.
  4. Chin to crown: with your jaw closed, straight up from the bottom of your chin to the top of your head.
  5. No calipers? Print the head calipers or the gauge strip in step 4.

The values shown are only a starting point. Measure your own head; 25.4 mm is one inch.

6.0 mm

The foam or padding you’ll fit inside, on each side. It is added twice to length and width, and once over the crown. Measure your padding.

Hat size

57 cm · US 7⅛ · UK 7 · EU 57

Convert from a hat size

Sets “Around your head” from the hat size. A hat size gives only the circumference; you still need length and width for the scale.

The model

The helmet or mask

Measure inside the model at 100 % in your slicer or a 3D viewer, at eye level.

From the bottom edge up to the inside of the crown.

Inside width of the neck opening; 0 if you don’t know.

3.0 mm

Used to estimate the outside size for the printer check.

No model loaded yet.

Up axis in the file
Front to back runs along
50 %

Of the model’s height from its lowest point. Set it where your eyes and temples will sit: usually 40–60 % for a full helmet.

Check the drawing in step 3: it should show a ring round your head. If it doesn’t, the file is probably lying on its side, so change the up axis.

Scale

Working out the scale…

Fits length, width and height each exactly, but stretches the design.

Otherwise pick your printer below the preview.

Print a part

Print

A thin ring with the helmet’s inside at your new scale, at the slice height. Try it on before printing the whole helmet: it should sit round your head with room for the padding.

15 mm
2.4 mm
Print it

Halves fit smaller beds: tape them together at the sides.

A flexible strip with millimetre marks, best printed in TPU. Loop it round your head, push the tail through the slot and read the circumference in the slot. Numbers are centimetres. Long strips come in pieces with sleeves to join them.

50 cm
65 cm
1.2 mm

The marks allow for the strip bending round your head, so keep the printed thickness true.

14.0 mm

A ruler with a fixed jaw at zero and a sliding jaw. Hold both jaws against your head and read the ruler at the sliding jaw’s edge nearest zero. Measures length, width and chin to crown.

26 cm
110 mm

Long enough to reach past your ears to the widest part of your head.

Colours

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The method

    How to scale a helmet to fit your head

    Downloaded helmets and masks are made at someone else’s size. The calculator compares your head, plus the padding you’ll add, with the inside of the model, and gives the scale to type into your slicer.

    1. Measure your head: length front to back, width side to side, chin to crown, and the circumference as a check.
    2. Measure the model: type its inside sizes, or load its STL and set the slice to eye level. The inside wall is traced from the middle of the slice outwards; eye and visor openings are bridged.
    3. Read the scale. The uniform scale is the larger of needed length ÷ inside length and needed width ÷ inside width, so the tighter direction just fits and the other has room to spare.
    4. Print the test ring and try it on before you spend a spool on the helmet.
    5. Check the bed. If the scaled helmet is too big for your printer, cut it into parts with the STL splitter.

    The maths

    Uniform and separate scales

    needed length = head length + 2 × padding
    needed width = head width + 2 × padding
    uniform scale = max(needed length ÷ inside length, needed width ÷ inside width)

    Separate scales set X to the width ratio, Y to the length ratio and Z to (chin to crown + padding) ÷ inside height. They fit every direction exactly, but stretch the design: round eyes turn oval and details lose their proportions. Keep them within a few percent of each other.

    The circumference is a check: an ellipse of your length and width should be close to your tape measurement. Heads are not perfect ellipses, so a few percent either way is normal.

    Hat sizes

    Hat sizes and head circumference

    HeadUK hat sizeUS hat sizeEuropean size
    55 cm (21.7 in)6¾6⅞55
    56 cm (22.0 in)6⅞756
    57 cm (22.4 in)77⅛57
    58 cm (22.8 in)7⅛7¼58
    59 cm (23.2 in)7¼7⅜59
    60 cm (23.6 in)7⅜7½60
    61 cm (24.0 in)7½7⅝61
    62 cm (24.4 in)7⅝7¾62
    63 cm (24.8 in)7¾7⅞63

    Each centimetre of head circumference is one eighth of a US hat size (US size = cm ÷ 8), and UK sizes run one eighth smaller than US. A European hat size is the circumference in centimetres. Hat makers’ charts differ a little; the calculator extends the chart from 48 to 66 cm with the same rule.

    Printable tools

    The test ring, gauge strip and calipers

    • Test ring: the helmet’s inside at the slice height, at your new scale. It should go round your head with room for the padding. Too tight? Add padding space or scale up; too loose, the reverse.
    • Head gauge strip: print it flat in TPU. Loop it round your head with the marks outside, push the tail through the slot and read the size in the slot. Strips longer than your bed come in pieces; slide a sleeve over each joint, butting the ends together. Every joint sits before the marks, so no sleeve has to pass the slot.
    • Head calipers: print the ruler flat and the sliding jaw standing up, as laid out; neither needs supports. A ruler longer than your bed comes in two pieces with a dovetail that is flush on both faces; glue it. Slide the jaw on from the far end.

    Printing

    Printing tips

    • Fine marks: the millimetre marks need a 0.4 mm nozzle and 0.12–0.2 mm layers to read cleanly.
    • Check the printer: measure the printed ring or a calipers reading against a ruler. Printers can come out a fraction small.
    • Big helmets: scaling up grows every direction, including height. Check the printed size against your bed before slicing.
    • Padding: measure your foam before you choose the comfort space; thick foam can need 10 mm or more each side.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits. Your model is read on this device and never uploaded.

    Will it fit my printer?

    Pick your printer below the preview, or type your bed size, and the scale step says whether the scaled helmet fits. If not, the STL splitter cuts it into parts with pin holes.

    Why does the uniform scale leave room on one side?

    A uniform scale grows every direction by the same amount. It is set by the tighter direction, so the other one ends up with spare room. Fill it with padding, or use separate scales if a few percent of stretch is acceptable.

    Can I sell helmets I print?

    The gauge, calipers and test rings you make here are yours. A helmet or mask model belongs to its designer: check its licence before selling prints of it.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-12. Community posts are one maker's experience, not a specification.

    1. Measurement procedures: head circumference, head breadth, head length and head height NIST, AnthroKids anthropometric data
    2. Hat sizing info The Hat Company
    3. How to determine your hat size Village Hat Shop
    4. Hat size Wikipedia
    5. SIL Open Font License SIL International