Free generator · Runs in your browser

Desk organizer generator A place for everything.

Measure your desk, a drawer or the space under your monitor, list what you keep there, and get a packed set of modules sized to your pens, phone, notes, cards, tape and cables, keyed together and ready to print.

  • Private by designNothing leaves this device
  • A whole setModules, fill trays and keys packed to fit
  • No supportsEverything prints as laid out
  • Ready to sliceEach module its own named object

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Where it goes

Fill

Measure the part of the desk you want to fill, usually behind the keyboard.

300 mm
160 mm

Pull-out drawers the size of the whole organizer, which stands on top of them.

50 mm

Measure the inside of the drawer: wall to wall, and from the floor to just under the desk top when it is shut.

300 mm
400 mm
60 mm

Measure your monitor’s stand and the height you want under the shelf, such as a keyboard tucked under it.

500 mm

Wider than your monitor’s foot. Longer shelves are cut into pieces that fit your printer, keyed together underneath.

220 mm
90 mm
70 mm
2

The shelf is a desk stand, not a lifting device: it holds a monitor’s foot sitting still on it. Print it with at least four walls and 25% infill, and check that it sits steady before you rely on it.

Items

4

Each item becomes its own module.

Item 1
12

Measure across the widest pen or marker you keep.

Measure across the phone in its case.

In its case, at the thickest point.

15 °

Square pads only. Measure one side.

Measure a full pad lying flat.

Press 20 cards together, measure and divide by 20.

Measure the outside of the roll, or of your tape dispenser.

Measure the plug or charging brick you park here.

2

Notches in the back wall, so cables run out behind the organizer.

2

Close the scissors and measure across the blades at the widest point, just below the pivot.

Measure at the pivot screw.

How deep the slot holds it. About half the blade or a fifth of the ruler holds well.

Measure the widest point of the pot.

Item 2
12

Measure across the widest pen or marker you keep.

Measure across the phone in its case.

In its case, at the thickest point.

15 °

Square pads only. Measure one side.

Measure a full pad lying flat.

Press 20 cards together, measure and divide by 20.

Measure the outside of the roll, or of your tape dispenser.

Measure the plug or charging brick you park here.

2

Notches in the back wall, so cables run out behind the organizer.

2

Close the scissors and measure across the blades at the widest point, just below the pivot.

Measure at the pivot screw.

How deep the slot holds it. About half the blade or a fifth of the ruler holds well.

Measure the widest point of the pot.

Item 3
12

Measure across the widest pen or marker you keep.

Measure across the phone in its case.

In its case, at the thickest point.

15 °

Square pads only. Measure one side.

Measure a full pad lying flat.

Press 20 cards together, measure and divide by 20.

Measure the outside of the roll, or of your tape dispenser.

Measure the plug or charging brick you park here.

2

Notches in the back wall, so cables run out behind the organizer.

2

Close the scissors and measure across the blades at the widest point, just below the pivot.

Measure at the pivot screw.

How deep the slot holds it. About half the blade or a fifth of the ruler holds well.

Measure the widest point of the pot.

Item 4
12

Measure across the widest pen or marker you keep.

Measure across the phone in its case.

In its case, at the thickest point.

15 °

Square pads only. Measure one side.

Measure a full pad lying flat.

Press 20 cards together, measure and divide by 20.

Measure the outside of the roll, or of your tape dispenser.

Measure the plug or charging brick you park here.

2

Notches in the back wall, so cables run out behind the organizer.

2

Close the scissors and measure across the blades at the widest point, just below the pivot.

Measure at the pivot screw.

How deep the slot holds it. About half the blade or a fifth of the ruler holds well.

Measure the widest point of the pot.

Item 5
12

Measure across the widest pen or marker you keep.

Measure across the phone in its case.

In its case, at the thickest point.

15 °

Square pads only. Measure one side.

Measure a full pad lying flat.

Press 20 cards together, measure and divide by 20.

Measure the outside of the roll, or of your tape dispenser.

Measure the plug or charging brick you park here.

2

Notches in the back wall, so cables run out behind the organizer.

2

Close the scissors and measure across the blades at the widest point, just below the pivot.

Measure at the pivot screw.

How deep the slot holds it. About half the blade or a fifth of the ruler holds well.

Measure the widest point of the pot.

Item 6
12

Measure across the widest pen or marker you keep.

Measure across the phone in its case.

In its case, at the thickest point.

15 °

Square pads only. Measure one side.

Measure a full pad lying flat.

Press 20 cards together, measure and divide by 20.

Measure the outside of the roll, or of your tape dispenser.

Measure the plug or charging brick you park here.

2

Notches in the back wall, so cables run out behind the organizer.

2

Close the scissors and measure across the blades at the widest point, just below the pivot.

Measure at the pivot screw.

How deep the slot holds it. About half the blade or a fifth of the ruler holds well.

Measure the widest point of the pot.

Item 7
12

Measure across the widest pen or marker you keep.

Measure across the phone in its case.

In its case, at the thickest point.

15 °

Square pads only. Measure one side.

Measure a full pad lying flat.

Press 20 cards together, measure and divide by 20.

Measure the outside of the roll, or of your tape dispenser.

Measure the plug or charging brick you park here.

2

Notches in the back wall, so cables run out behind the organizer.

2

Close the scissors and measure across the blades at the widest point, just below the pivot.

Measure at the pivot screw.

How deep the slot holds it. About half the blade or a fifth of the ruler holds well.

Measure the widest point of the pot.

Item 8
12

Measure across the widest pen or marker you keep.

Measure across the phone in its case.

In its case, at the thickest point.

15 °

Square pads only. Measure one side.

Measure a full pad lying flat.

Press 20 cards together, measure and divide by 20.

Measure the outside of the roll, or of your tape dispenser.

Measure the plug or charging brick you park here.

2

Notches in the back wall, so cables run out behind the organizer.

2

Close the scissors and measure across the blades at the widest point, just below the pivot.

Measure at the pivot screw.

How deep the slot holds it. About half the blade or a fifth of the ruler holds well.

Measure the widest point of the pot.

Layout and joints

Module sizes

On the grid every module is a whole number of 42 mm steps (less 0.5 mm), the same pitch as common grid storage bins, so modules swap places. Their own size packs tighter.

Joined by

Keys are small printed pieces that press into sockets under two neighbouring modules. A base tray holds every module in one keyed tray instead.

1.0 mm

Added to every item’s size. Memory card and USB slots use a fixed 0.6 mm so cards stay put.

2.0 mm
2.0 mm

With keys the floor is at least 3.4 mm, so the sockets fit under it.

Packing plan

The plan appears here once the preview is built.

Style

Corners
Heights
15 mm
On the front

Raised on a sloped plate at the front. A monogram uses the first three letters.

Typeface

Colours and view

Modules
Keys, letters and drawers
Preview

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The method

    How to plan a desk organizer

    Measure the space and list what you keep on the desk. The generator sizes a module for each item, packs them in rows with the tallest at the back, fills the gaps with open trays, adds the keys that hold them together and lays everything out on your printer’s plates.

    1. Measure the space: a strip of desk, the inside of a drawer, or the shelf you want for a monitor riser.
    2. Add your items and measure the ones that vary: your phone in its case, your tape roll, your charger, your scissors.
    3. Check the packing plan. It shows every module from above and lists anything that does not fit.
    4. Pick a style: rounded or angular, stepped heights, a name plate.
    5. Download and print. Every module is its own object in the 3MF, named after what it holds.

    Items

    What each module holds

    ItemPocketYou measure
    Pen cupA cup for the pens, 90 mm tallThe thickest pen
    Phone slotA slot leaning back, with a gap in the front lip for the cableThe phone in its case
    Sticky notesA square pocket with a finger notchThe pad height
    Business cardsCards standing on the long edge, with a thumb notchHow many cards and their thickness
    Tape roll bayA round pocket the roll or a small dispenser lies inThe roll across and its width
    Charger and cablesA pocket with notches for cables out of the backThe charger and thickest cable
    Clips and traysOpen compartmentsTray size for an open tray
    Scissors and rulerA deep narrow slotBlade or ruler width and thickness
    Memory cards and USBRows of slots that hold each card or plug by its edgeNothing: sizes are published
    Plant potA round pocketThe pot

    Sizes

    Sizes and settings

    SettingDefaultWhat it does
    Clearance1 mmAdded to every item’s width and depth
    Grid42 mmModules are whole steps less 0.5 mm, so neighbours never rub
    Key fit0.15 mm a sideThe key is the socket shrunk by this much; it presses in by hand
    Key thickness1.9 mmIn a 2.2 mm socket, so the modules, not the keys, stand on the desk
    Stepped heights15 mm a rowEach row is at least this much lower than the one behind it

    Sticky notes default to the common 3 × 3 inch square (76.2 mm). Business cards have no single standard; these are the usual sizes by region:

    RegionSize
    US and Canada88.9 × 50.8 mm
    Western Europe85 × 55 mm
    Credit-card size85.6 × 53.98 mm
    Japan91 × 55 mm

    Memory card slots use the published card sizes (24 × 2.1 mm and 11 × 1 mm edges); USB slots use the plug sizes (12 × 4.5 mm and 8.25 × 2.4 mm). Phones, pens, tape, chargers, scissors and pots differ, so the generator asks you to measure them. The numbers in the presets are examples only.

    Printing

    Printing tips

    • No supports: modules print upright as laid out. The key sockets under each floor are short bridges that print cleanly without supports.
    • Keys: print them flat. If they are tight, sand an edge; if loose, a drop of glue holds them.
    • Test first: print the phone slot or the card module first to check your items fit.
    • Drawer units and riser legs print lying on their backs, so their openings face up and need no supports. They are tall prints: check your printer’s height.
    • Riser shelf: it prints upside down, with the leg recesses and key sockets facing up. Use at least four walls and 25% infill.
    • Filament: the estimate assumes about two walls and 15% infill. Tall modules with shallow pockets are mostly infill below the pocket, so they print faster than they look.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits.

    Will it fit my printer?

    Choose your printer below the preview. Modules, keys and pieces are laid out on as many plates as they need, and long shelves and trays are cut into keyed pieces that fit the bed. A part bigger than the bed is flagged.

    Can I sell organizers I make?

    The designs you make are yours. The typefaces are open-licensed, which allows making physical products. Don’t put other companies’ names or logos on organizers you sell.

    Will the modules fit grid storage bins?

    On the 42 mm grid the modules have the same footprint steps as common grid bins, so they sit side by side with them. They have flat bottoms, not the stepped feet that lock into a grid baseplate.

    Something does not fit. What can I change?

    Try modules at their own size instead of on the grid, a shallower item, fewer items, or turn off the name plate. The plan lists each item that does not fit and why.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-12. Community posts are one maker's experience, not a specification.

    1. Sticky note sizes (encyclopedia article on the original note pads) Wikipedia
    2. Business card sizes Wikipedia
    3. SD card sizes Wikipedia
    4. USB hardware: plug sizes Wikipedia
    5. gridfinity-rebuilt-openscad (42 mm grid specification) GitHub
    6. Modeling with 3D printing in mind Prusa Research
    7. SIL Open Font License SIL International