Free generator · Runs in your browser

Device mount generator Sized to your device.

Measure your router, power brick, hub, console or remotes and make a wall cradle, under-desk sling, corner brackets, strap plate or remote holder that fits, with windows for cables and screw holes you can reach.

  • Private by designNothing leaves this device
  • Five stylesCradles to remote holders
  • No supportsLaid out to print as is
  • Ready to sliceSTL and 3MF files

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Device

Mount style

The device stands in a holder on the wall and drops in from above, like a router on its edge. Depth is how far it sticks out from the wall.

The device lies flat under the desk and slides in from the front. Depth is front to back; height is top to bottom.

The device lies flat against the wall; a clip holds each corner. Depth is how thick it is, off the wall.

The device sits against a plate and a hook-and-loop strap goes round it. Depth is how far it sticks out from the wall.

Measure the device at its widest points, including feet, bumps and plugs that stick out.

0.0 mm

For a device with rounded corners. The pocket corners follow it.

3

Measure across the widest part of the buttons side, and the thickest point front to back.

60 mm

How far each remote drops in. About a third of its length holds it well.

1.0 mm

The inside is the device plus this on each side. 1 mm slides in easily; less holds tighter.

Shape

25 mm

How far the front wall rises above the floor. Lower shows more of the device.

60 %

Taller side walls hold a tall device more securely. They are never lower than the front lip.

40 mm
0 mm

Negative moves it left, positive right, as you face the wall.

6 mm

Height of the wall left under the window. The window is open at the top, so it prints without supports.

Side windows (for cables)
20 mm
6 mm
40 mm
15 mm
0 mm

A cradle wider than the bed is cut into parts joined by floor dovetails. Too big for 3 parts, or too deep, and it becomes corner brackets.

Form

With a desk-edge clamp, it is two clamp hooks over the desk’s front edge. The device slides in from the right.

30 mm

L-hooks run front to back under the device; clamp hooks run along the desk edge.

15 mm

How far each L-hook reaches in under the device.

6 mm

The device slides in from the front until it meets the stop.

Clips
25 mm
6.0 mm

Keep it clear of buttons, lights and screens near the corners.

2.4 mm

Measure your hook-and-loop strap. The slots are 1.5 mm wider.

Measure it with the hook and loop sides pressed together.

2
Plates

One small plate per strap uses less plastic and fits any printer under a long device.

Holds the device in place while you do up the strap.

10 mm
0.8 mm
Typeface
3.0 mm
3.0 mm

Mount

Fix it with

Head sizes from DIN 7997. For other screws or a nail, choose Measured and measure the head and shank.

Measure your adhesive pads; the parts they go on are made big enough to carry them.

Drop-lock pegs for pegboards with upright 5 × 15 mm slots on a 40 mm pitch. Push them in, then slide the mount down to lock.

A keyhole in each ear hangs over a screw head, so the mount lifts off the wall.

Measure the desk top’s front edge with calipers or a ruler.

0.4 mm

The gap between the jaws is the desk plus this. A small ridge on the lower jaw grips the desk.

4.0 mm
5.0 mm

Screw holes always sit outside the device’s outline, so you can reach every one.

Colours

Preview

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The method

    How to make a mount that fits your device

    Printable mounts are usually made for one model. Here you measure your own device, and the mount is built round it: the inside is the device plus the clearance you choose, with windows where its cables and lights are and fixings where you can reach them.

    1. Pick a style: a wall cradle, an under-desk sling, corner brackets, a strap plate or a remote holder.
    2. Measure the device at its widest points, including feet and plugs, and set the clearance.
    3. Add windows and vents for cables, ports and lights.
    4. Choose the fixing, pick your printer below the preview, then download and print as laid out.

    Styles

    Which style for which device

    StyleGood forHow it holdsPrints
    Wall cradleRouters, hubs, streaming boxes, consoles, phonesAn open-front holder the device drops intoStanding up, no supports; split into parts if wide
    Under-desk slingPower bricks, hubs, small PCsTwo L-hooks, a U tray, or two clamp hooks over the desk edgeOn its side, no supports
    Corner bracketsBig flat devices: routers, switches, tabletsA clip on 2 or 4 corners, with a lip over the frontFront face down, no supports
    Strap mountPower strips, hubs, odd shapesA hook-and-loop strap through slots in a plateFlat; the strap channels bridge
    Remote holder1 to 4 remotes or controllersA pocket for each, with a thumb notchStanding up, no supports

    Sizes

    What you measure, and what it sets

    You measureIt sets
    Device width, height, depthThe inside: device + clearance on every side
    Corner radiusThe pocket and clip corners follow the device’s rounded corners
    Remote width and thicknessEach pocket, on its own
    Strap width and thicknessSlots 1.5 mm wider and taller, and a channel on the back
    Desk thicknessThe gap between the clamp’s jaws: desk + clamp clearance
    Screw or pad sizeCountersunk holes, keyholes, or ears big enough for the pad

    There is no standard size for routers, power bricks or remotes, so every default here is only a starting point. Measure yours with calipers or a ruler.

    Fixings

    Screw hole sizes

    ScrewHead (DIN 7997)Clearance holeCountersink
    3 mm5.6 mm3.5 mm6.2 mm
    4 mm7.5 mm4.5 mm8.1 mm
    5 mm9.2 mm5.5 mm9.8 mm
    6 mm11 mm6.5 mm11.6 mm
    3.5 mm6.5 mm4.0 mm7.1 mm
    4.5 mm8.3 mm5.0 mm8.9 mm

    Head diameters are the nominal sizes in DIN 7997 for countersunk wood screws. The hole is 0.5 mm bigger than the thread and the countersink 0.6 mm bigger than the head. Corner clips have a deep counterbore, so use a screw long enough to reach through the clip and into the wall plug. Pegboard pegs fit upright 5 × 15 mm slots on a 40 mm pitch.

    Heat

    Warm devices: keep the air moving

    Routers, power bricks, consoles and hubs get warm. Leave space round them and keep their vents open: don’t box a device in tighter than its maker allows. How much room a device needs is in its manual, so check it before you mount it. The cradle’s vent slots and open top help, but they don’t replace that advice.

    • PETG near warm devices: Prusa’s material guide says PLA gets soft and deforms above 60 °C, while PETG has good temperature resistance for parts below 80 °C.
    • Power strips and bricks stay in the open, never covered. Don’t pull the cords tight round a mount.

    Printing

    Printing tips

    • As laid out, no supports: cradles and remote holders stand up with every wall vertical, and their windows are open at the top; slings and clamp hooks lie on their side so the layers run round each bend; corner clips print front face down, with a 45° countersink in the counterbore.
    • Strap plates print flat on their back, so the strap channels are bridged: about the strap’s width, which most printers bridge cleanly.
    • Walls over infill: 4 or more walls make a mount stiffer than extra infill.
    • Split cradles: slide the parts together at the floor dovetails and glue the joints.
    • Two colours: the remote holder’s label is its own object in the 3MF, or pause at its first layer to swap filament.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits.

    Will it fit my printer?

    Choose your printer below the preview. A cradle wider than the bed is cut into parts joined by dovetails; one that would need more than three parts, or is deeper than the bed, is made as corner brackets instead. Remote holders split into separate holders, and strap mounts can use one small plate per strap.

    How much will it hold?

    We don’t give load ratings. It depends on the plastic, the walls, the print, the wall and the fixings. Test a mount with more than the device weighs before you trust it, and don’t hang anything heavy on adhesive pads alone.

    Does it work for any device?

    Any device that is roughly a box. Measure it at its widest points, including feet, bumps and plugs that stick out, and add windows where its cables and lights are.

    Can I sell mounts I print?

    The designs you make are yours. The typefaces are open-licensed, which allows making physical products. We make no claims about load, heat or safety, so test anything you sell and don’t promise more than you have tested.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-12. Community posts are one maker's experience, not a specification.

    1. DIN 7997: cross-recessed countersunk head wood screws, dimensions fasten.it
    2. PLA Prusa Research
    3. PETG Prusa Research
    4. Modeling with 3D printing in mind (orientation and strength) Prusa Research
    5. boxes.py slot pegboard generator (slot layout) Florian Festi
    6. Slot pegboard network mounts (drop-lock peg geometry) PrimroseHA (GitHub)
    7. Extension cord safety fact sheet Texas Department of Insurance
    8. SIL Open Font License SIL International