Free generator · Runs in your browser

Bobblehead generator Anything can bobble.

Add a printed spring and a named plinth to any figure you already have, cut at the neck, or start from a simple built-in person, cat, dog or robot. The socket, post and balance are worked out for you.

  • Private by designYour figure never leaves this device
  • Any figureOr four built-in characters
  • Balance checkCentre of mass over the spring
  • Ready to sliceEach part its own object

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Figure

Make
Character
44 mm

The body and plinth grow with it.

Figure in use

Only remix figures you are allowed to change: check the designer’s licence first.

What bobbles
120 mm

Your file is scaled to this height.

Which way is up in the file
Cut
62.0 %

Above the cut bobbles; below stays put. Choose “Show the cut” under the preview options to see the plane.

Spring

Spring
Shape
14.0 mm
10.0 mm

The narrow end goes up into the head.

1.4 mm

Wider or taller wire makes a stiffer spring.

1.2 mm
4

More turns: softer and bouncier.

20.0 mm
Print it in

Measure your spring with calipers. The socket and post are sized from these numbers.

12.00 mm
0.80 mm
25.0 mm
8
0.20 mm

Gap on each side between the spring and the socket or post. Lower for a press fit.

4.0 mm
4.0 mm

Balance

Spring under

Under the centre of mass the head bobbles straight. The readout shows how far it leans otherwise.

0.0 mm
0.0 mm

Plinth and name

The body’s feet are trimmed flat and get a hole for the plinth’s locating peg.

Shape
84 mm

Grows if the figure or the name needs more room.

72 mm
12.0 mm
8.0 mm
Typeface
Weight against tipping

Sizes from the mints’ published specifications. Worn coins differ a little: check yours.

24.00 mm
1.75 mm
2
1
0.15 mm

Colours and view

Preview

“Show the cut” works for a figure cut at the neck. Downloads are always laid out flat, each part its own object.

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The method

    How to make a bobblehead

    A bobblehead is a head on a spring. This generator makes the spring, a socket in the head for its top end, a post on the body for its bottom end, and a weighted plinth with a name. It needs no AI: bring any figure you already have, or start from a simple built-in character.

    1. Choose the figure: a built-in person, cat, dog or robot, or your own STL, 3MF or OBJ. Your file is read on this device and never uploaded.
    2. Cut it: the generator finds the neck, or you set the height. Both cut faces are closed flat. Or keep the figure whole and stand it on the spring.
    3. Pick the spring: print a helical or conical one, or measure a metal spring you have.
    4. Check the balance: the readout shows whether the head’s centre of mass sits over the spring.
    5. Add the plinth: its shape, your name and a coin or nut weight. Download, print and put it together.

    Sizes

    Spring, socket and post sizes

    PartSizeWhy
    Socket in the headSpring’s top outside diameter + 2 × clearanceThe spring’s top end presses in; a drop of glue holds it
    Post on the bodySpring’s inside diameter − 2 × clearanceThe bottom end slides over it
    Clearance0.2 mm each side to startPrinted holes come out a little small; print a test and adjust
    Metal springYour measured outside and wire diametersMeasure with calipers; springs vary
    Coin pocketCoin diameter + pocket clearance, stack thickness + 0.2 mmCoin sizes from the US Mint and the European Commission
    Nut pocketWidth across flats + pocket clearanceISO 4032 hex nuts
    CoinDiameter (mm)Thickness (mm)
    US 1 cent19.051.52
    US 5 cents21.211.95
    US 10 cents17.911.35
    US 25 cents24.261.75
    1 euro23.252.33
    2 euro25.752.2

    Balance

    Balance and stiffness

    A head bobbles straight when its centre of mass is right over the spring. The generator adds up the head’s volume to find that point and shows how far it is from the spring, in millimetres. With Spring under: the head’s centre of mass the socket goes there for you; otherwise move the post by the amount shown. The head’s weight is for a solid print; normal infill makes it lighter.

    The stiffness readout compares your spring with the default one, from its wire size, diameter and turns. It is a relative guide, not a measured spring rate: plastic, temperature and print settings change it a lot, so test the spring with the head on it.

    Printing

    Printing tips

    • The spring: TPU for a soft, lively bobble; PETG for a firmer one. Upright, 100% infill, fine layers. Not PLA: it creeps and sags.
    • Test the spring first: it is a quick print, and it tells you whether to add wire or turns.
    • The head: print it flat face down; the socket bridges.
    • Your figure: its own overhangs may still need supports, as they did before.
    • Put it together: spring onto the post, head onto the spring, body onto the plinth’s peg, coins or nut in the pocket. Glue as needed.

    Remixing

    Respect the original designer

    Only remix figures you are allowed to. Many shared models carry a licence: some allow changes, some do not (no derivatives), and some do not allow selling (non-commercial). Check the licence where you downloaded the model, and credit the designer when you share your bobblehead.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits. Your figure stays on your device.

    Will it fit my printer?

    Choose your printer below the preview. The parts are laid out on its plates; a tall figure can be made smaller with Figure height.

    Can I sell bobbleheads I print?

    The built-in characters and the parts you make are yours. The typefaces are open-licensed, which allows making physical products. An uploaded figure keeps its own designer’s licence: you may only sell it if that licence allows. No claims beyond that: check toy-safety rules before selling for children.

    Which spring should I use?

    Start with the default printed spring in TPU. A heavy head may need a stiffer spring: wider or taller wire, or fewer turns. A metal spring from a hardware kit works too: measure it and choose Use a metal spring.

    Is it safe for small children?

    No. It has small parts, a spring and coins or nuts: not for children under 3. We make no toy-safety claims.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-12. Community posts are one maker's experience, not a specification.

    1. The challenges of 3D printing reliable springs Hackaday
    2. How to design 3D printed springs: tips and materials Siraya Tech
    3. Torsion constant (rectangle approximation) Wikipedia
    4. Coin specifications United States Mint
    5. Common sides of euro coins European Commission
    6. DIN EN ISO 4032 hexagon nuts fasten.it
    7. About CC licenses Creative Commons
    8. Small parts ban and choking hazard labeling US Consumer Product Safety Commission
    9. SIL Open Font License SIL International