Free generator · Runs in your browser

Lithophane generator Turn a photo into light.

Turn any photo into a print-ready lithophane: a flat panel, a curved display or a lamp shade. See it lit before you print, then download STL or 3MF.

  • Private by designYour photo never leaves this device
  • See it litA backlit preview of the finished print
  • Three formsFlat, curved or lamp, with six outlines
  • Ready to sliceWatertight STL and 3MF files
Preview
Light colour

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Triangles
—
Fits
—

Start from

Photo

Pick Framing above the preview to drag the photo into place.

1.00 ×

Shape

Form
Outline

Size

Proportions

Print orientation

Standing gives finer detail on small and mid-size panels; large panels often print better flat.

Thickness

0.8 mm

Keep at least two lines of your nozzle: 0.8 mm suits a 0.4 mm nozzle.

3.0 mm

Thicker gives deeper blacks but needs a brighter light.

3.0 mm
3.5 mm

A frame slightly thicker than the image stiffens the panel and reads as a crisp edge.

Tone

Thickness curve

Natural light compensates for how light fades through plastic, so midtones stay open. How it works

Stretches the photo’s darkest and brightest tones across the full thickness range.

0.00
1.00 ×
1.00 ×

Above 1 lifts shadows; below 1 deepens them.

0.30

Crisps edges and fine detail; raise it for soft or small photos.

Detail and download

Detail

Add a photo to see the file size.

Slicer starting points

  • 100% infill, so no gaps show once lit.
  • 0.10–0.12 mm layers.
  • White or natural PLA.
All print settings

Your photo is processed on this device and is never uploaded.

Advertisement

The method

Make a lithophane in five steps

A lithophane is a thin panel whose thickness follows a photo. Held up to a light, thin areas glow and thick areas stay dark, so the picture appears only when it is lit. This generator does the conversion in your browser and gives you a solid, print-ready model.

  1. Add a photo. Drop it on the page, paste it, or try the sample scene. Nothing is uploaded.
  2. Pick a form. A flat panel for frames and windows, a curved panel that stands by itself, or a cylinder lamp shade.
  3. Frame it. Choose Framing above the preview and drag the photo until the subject sits where you want it.
  4. Check it lit. Light on shows how the panel will look with a light behind it. Adjust tone until faces and highlights read clearly.
  5. Download and slice. Export STL or 3MF, then print solid with fine layers (settings below).

Contrast

Choosing the thinnest and thickest points

The thinnest point sets how bright the highlights get. Around 0.8 mm is a common default, and it should stay at least two extrusion lines thick so it prints solid: with a 0.4 mm nozzle, that means about 0.8 mm.

The thickest point sets how dark the shadows get. Around 3 mm is typical. Going thicker deepens the blacks but makes the whole panel dimmer, so it needs a brighter light; going thinner gives a lighter, lower-contrast image that works with a weak light.

A frame a little thicker than the image keeps a thin panel flat and stiff, and gives the edge a clean outline. Set the frame width to 0 for a borderless panel.

The science

Natural light vs linear thickness

Light does not fade evenly as plastic gets thicker. It falls off exponentially, as described by the Beer–Lambert law: each extra millimetre absorbs the same share of whatever light is left. A linear mapping, where thickness rises evenly from white to black, therefore crowds the midtones into the dark end and can make portraits look heavy.

Natural light spaces the thickness so the light that gets through rises evenly with the photo's brightness instead. For a brightness b between 0 and 1, the thickness is

t = −ln( D + b·(L − D) ) ÷ k, where D = e−k·max and L = e−k·min

Here k is how quickly light fades in the plastic. The generator uses 0.8 per millimetre as a typical value for white PLA; the real figure varies by brand and colour, so treat the preview as a close guide rather than a measurement. Both curves give exactly your thinnest and thickest values at pure white and pure black.

Form

Flat, curved or lamp?

Flat panel

Fits a frame, a window or a light box. Choose an outline from rectangle to heart, and print it standing or lying flat.

Curved panel

Stands by itself and looks good from a wider angle. A 90–150° curve is a good balance of stability and viewing width.

Lamp shade

A cylinder that sits over a light. The generator reports its inner diameter, so measure your light first; the seam sits at the back.

Input

Picking the right photo

  • One clear subject. Faces and pets work best when they fill most of the frame.
  • Good contrast. Separate light and dark areas read clearly once lit; a flat, grey photo stays flat.
  • Simple backgrounds. Busy backgrounds turn into noise at lithophane resolution.
  • Not too much black. Large dark areas print thick, use more filament and take longer.
  • Enough pixels. About 1,000 pixels across is plenty for a 150 mm panel at standard detail.

Display

Lighting your lithophane

Use an LED, which stays cool, rather than a candle or a hot bulb: PLA softens at fairly low temperatures, so keep heat away from the panel. A diffused light a few centimetres behind the panel gives the most even glow. If the centre looks brighter than the edges, move the light back or add a diffuser. Warm white light gives the classic porcelain look; daylight white shows more neutral greys.

Questions, answered

Is the lithophane generator free?

Yes. There is no account, watermark or download limit.

Is my photo uploaded anywhere?

No. The photo is read, framed and converted into a 3D model entirely on your device, inside your browser. It is not sent to 3Dprintsy or anyone else.

Should I download STL or 3MF?

Both are ready to slice. 3MF files are smaller and record that the units are millimetres; STL opens in every slicer, including older ones.

Why does my printed lithophane look too dark?

Usually the light is too weak for the thickness. Try a brighter or closer light, reduce the thickest point, switch on auto levels, or raise the midtones. The Light on preview helps you compare settings before printing.

Can I print a lithophane on a resin printer?

Yes. Resin lithophanes can be very detailed. Use a light-coloured resin and your usual resin supports and exposure settings, and print the panel solid.

What size should my first lithophane be?

Start around 100 mm wide at standard detail. It prints in a few hours on most printers and shows whether your thickness and light settings work before you commit to a large panel.

Why is the 3D file so large?

A lithophane needs a fine grid to hold photo detail, so it has many triangles. Draft and standard detail are enough for most panels; fine and ultra mainly help small panels and very fine nozzles.

Sources

Print advice is a starting point drawn from these references, checked on 2026-11-07. Community posts are one maker's experience, not a specification.

  1. How to 3D print a lithophane: a beginner’s guide Sovol
  2. Printing lithophanes: flat or vertical? Bambu Lab community forum
  3. Lithophane settings Prusa community forum
  4. PLA material guide Prusa Research
  5. Beer–Lambert law Wikipedia