Free generator · Runs in your browser

Fidget spinner generator Balanced by design.

Make a fidget spinner with 2 to 6 arms, on a 608 bearing or a printed pin, weighted with bearings, nuts or coins, with your name on it. Or make a spinning top. Every pocket is sized for you, and the balance is checked.

  • Private by designNothing leaves this device
  • Seven shapesOr your own outline
  • No supportsEvery part prints flat
  • Ready to sliceSTL and 3MF

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Make

Make
Shape
Arms
100 mm

The longer side of your shape.

Centre on

The bearing goes on the shape’s balance point, so it spins without shaking. Weights go as far out as the shape allows, and any that don’t fit are left out.

27.0 mm

Grown automatically if the pockets wouldn’t fit. Longer arms spin longer but need a bigger bed.

3.0 mm

A ring joins the arm tips, for a wheel look and more weight at the edge.

Shape
Tip
50 mm
18 mm

A shorter handle keeps the centre of mass low, for a steadier spin.

Centre

Spins on

608 is the common skateboard bearing (8 × 22 × 7 mm). 688 and R188 are smaller and lighter.

0.10 mm

Added to the bearing’s outside diameter. Lower for a tighter press fit.

Two caps press into the bearing’s inner ring, so you can hold it while it spins.

22.0 mm
0.10 mm

How much smaller the cap’s peg is than the bearing’s bore. Lower grips tighter; raise it if the caps won’t go in.

No bearing to buy: a pin is printed inside the body with a small gap, so it comes off the bed ready to spin. Be warned: it spins for seconds, not minutes. A ball bearing spins far better.

0.35 mm

Raise it if the pin fuses to the body; lower it if the spin wobbles. Our tolerance test finds your printer’s number.

A top needs no bearing: it spins on its tip. The handle pushes into a socket in the top.

0.10 mm

How much bigger the socket is than the 6 mm peg.

Weights

Weights in the arms
Weights in the rim
6

As many as fit are used, spaced evenly round the rim.

A 608 bearing in each arm: about 12 g each, and they spin a little themselves.

0.15 mm

Added to the weight’s size. Lower for a press fit.

Name

Names go on spinners: on the rim or the cap.

Name
6.0 mm

Shapes without a rim get an outer ring to carry the name.

Keeps the spinner balanced. One copy is fine for a short name.

Set into the top cap’s face. Initials or a short word fit best.

Typeface

Colours and view

Preview

The preview shows bearings, nuts and coins in grey and gold; they are not in the files. Downloads are always laid out flat to print.

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The method

    How to make a fidget spinner

    Pick a shape and the number of arms, choose the bearing in the middle and what weights the arms, and the generator sizes every pocket from published sizes, checks the balance and lays the parts out flat to print with no supports.

    1. Choose a shape: round lobes, blades, a star, a gear rim, a ring wheel, a flower, or your own outline.
    2. Choose the centre: a 608 skateboard bearing (or a smaller 688, 626 or R188), or a printed pin with nothing to buy.
    3. Weight the arms with 608 bearings, hex nuts or coins, or leave them solid.
    4. Add a name on the rim or the cap, pick colours and download.

    Sizes

    Bearing, nut and coin sizes

    PartSize (mm)Where it comes from
    608 bearing8 × 22 × 7 (bore × outside × width)Bearing maker’s data sheet
    626 bearing6 × 19 × 6 (bore × outside × width)Bearing dimension table
    688 bearing8 × 16 × 5 (bore × outside × width)Bearing dimension table
    R188 bearing6.35 × 12.7 × 4.762 (bore × outside × width)Bearing maker’s series page (¼ × ½ × 3⁄16 inch)
    M6 hex nut10 across flats, 5.2 tallISO 4032
    M8 hex nut13 across flats, 6.8 tallISO 4032
    M10 hex nut16 across flats, 8.4 tallISO 4032
    US 1 cent coin19.05 across, 1.52 thick, 2.5 gUS Mint
    US 5 cents coin21.21 across, 1.95 thick, 5 gUS Mint
    US 10 cents coin17.91 across, 1.35 thick, 2.268 gUS Mint
    US 25 cents coin24.26 across, 1.75 thick, 5.67 gUS Mint
    1 euro coin23.25 across, 2.33 thick, 7.5 gEuropean Commission
    2 euro coin25.75 across, 2.2 thick, 8.5 gEuropean Commission

    The bearing seat is the bearing’s outside diameter plus Seat clearance (0.1 mm by default), because printed holes come out a little small. Weight pockets add Pocket clearance the same way. Measure your parts with calipers if you can: coins wear, and bearings and nuts vary a little between makers.

    Options

    Shapes, weights and centres

    ChoiceWhat it doesGood for
    Round lobesThe classic shape: a pocket in each rounded armTwo to six arms, any weight
    Blades or starArms that sweep back or end in pointsA bold look; the star suits five arms
    Gear rim or ring wheelA solid wheel with windows between the weightsNames on the rim; most weight at the edge
    FlowerPetals between the armsA softer shape to hold
    Your outlineAny dark shape from an image or SVGLogos and silhouettes; check the balance readout
    608 bearing weightsAbout 12 g eachThe longest spin
    Hex nutsPressed into hex pockets; stack two for more weightCheap, easy to find
    CoinsA stack in a round pocketWhatever is in your pocket
    Printed pinPrinted in place, nothing to buyA quick print; it spins far less well than a bearing

    Balance

    Why balance matters

    A spinner shakes if its centre of mass is off the bearing. The generator adds up the plastic, the name and the weights, and shows how far the centre of mass is from the spin axis. Built-in shapes are balanced by design. Your own outline may not be: choose Centre on: balance point, and the bearing goes where the shape balances. Weights in every arm must match, and a name repeated on every arm keeps things even.

    For spinning tops, the readout shows how high the centre of mass sits above the tip. Lower spins steadier, so a short handle helps. Weights at the rim don’t lower it, but they store more spin, so the top keeps going longer.

    Printing

    Printing and assembly tips

    • No supports: the body prints flat; caps print face down; tops print upside down with the handle on its end.
    • Bearings: press them in square, with a vice or a flat block. Loose? Lower the clearance by 0.05 mm.
    • Longer spins: wash the grease out of the centre bearing with isopropyl alcohol, and use heavy weights far from the centre.
    • Print-in-place: print it slowly with a clean first layer, then twist the pin firmly to free it. If it’s stuck, raise the pin gap and print again.
    • Strength: 3 walls and 20–30% infill; PLA or PETG both work.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits.

    Will it fit my printer?

    Choose your printer below the preview. Most spinners are 70–110 mm across, so they fit almost any bed.

    Which spins longest?

    A clean 608 bearing in the middle, with heavy weights at the end of long arms. A printed pin spins for seconds, not minutes.

    Is it safe for small children?

    No. Spinners and tops are small parts with loose hardware: not for children under 3. We make no toy-safety claims.

    Can I sell spinners I print?

    The designs you make are yours. Bearings, nuts and coins are standard parts, and the typefaces are open-licensed, which allows making physical products. No claims beyond that: check toy-safety rules before selling for children.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-11. Community posts are one maker's experience, not a specification.

    1. 608 high precision ball bearing data sheet GMN Bearing USA
    2. Ball bearing dimension table (608, 688, 626) igus
    3. R188 series ball bearings NSK
    4. DIN EN ISO 4032 hexagon nuts fasten.it
    5. Coin specifications United States Mint
    6. Common sides of euro coins European Commission
    7. Small parts ban and choking hazard labeling US Consumer Product Safety Commission
    8. SIL Open Font License SIL International