Free generator · Runs in your browser

Balloon letter generator Puffed up, printed flat.

Make puffy balloon letters and numbers for birthdays and parties: one per letter in rainbow, gold or silver, or a joined word. Add bunting loops, a cake-topper stake or a desk stand, and print with no supports.

  • Private by designNothing leaves this device
  • Rounded everywhereThick and thin strokes alike
  • No supportsFlat backs print as they are
  • Ready to sliceEach letter its own colour

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Letters

One balloon per letter. A new line starts a new row (up to three rows and 30 letters).

Balloon letters are usually capitals. Lowercase dots are tied on so they don’t print loose.

Pieces

A rounded bar along the bottom ties every letter together.

-0.03 em

Below 0 the letters overlap and merge, like a tied bunch of balloons.

60 mm

The height of a capital letter. Pick your printer below the preview to check the plates.

Typeface
1.50 mm

Thickens every stroke for a fuller balloon. Capped at about 4.5% of the letter height so holes in A, B and O stay open.

Puff

100 %

How high each stroke domes, as a share of its half-width. 100% gives a round cross-section.

A narrow flat band where the dome starts, like the sealed edge of a foil balloon.

A small tied knot at the bottom. Not added with a stake or a stand.

Hang or stand

Add

One loop above each piece’s balance point, on a short stem where the letter dips, so it hangs straight.

Two loops at the top of each letter. Run one string through all of them for a banner that faces forward.

60 mm

How far the stake reaches below the letters. A joined word wider than 80 mm gets two.

0.30 mm

Extra room around the peg in the stand’s slot. Print a tolerance test to find your printer’s fit.

Colours

Colours

Letters take the colours in turn. A joined word takes the first one.

Preview

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The method

    How the balloon letters are made

    Each letter is drawn in your typeface, then puffed up like a balloon. Every point rises by how far it is from the letter’s edge, following a quarter circle sized to the stroke there, so thick strokes and thin ones both round over their centre line. The back stays flat, so each piece lies on the bed and prints with no supports.

    1. Type your letters or numbers, and choose one piece per letter or a joined word.
    2. Set the height and puffiness.
    3. Add loops, a stake or a stand for bunting, cakes or a shelf.
    4. Download and print. Each letter is its own object in its own colour.

    Options

    Ways to hang or stand them

    OptionWhat you getGood for
    Hanging loopOne loop above the balance point, on a short stem if the letter dips thereSingle letters, ornaments, garlands
    Bunting loopsTwo loops along the top of each letter, at the same heightBirthday banners on a string or ribbon
    Cake stakeA stake with a blunt point under each letter (two under a wide joined word)Cake and cupcake toppers, plant pots
    Desk standA peg under the letter and a separate stand with a slot sized to itShelves, desks, party tables
    Joined wordThe whole word as one piece, letters merged onto a rounded base barNames, cake toppers, signs

    Loops, stakes and stems scale with the letter height. At 60 mm, a loop takes string or ribbon up to about 6.6 mm across.

    Printing

    Printing tips

    • No supports: print every balloon flat on its back, dome up.
    • Shine: silk or metallic filament gives the foil-balloon look; three or more top layers keep the dome smooth.
    • Colours: each letter is its own object with its colour set. On one nozzle, print a colour per plate, or use a colour change for a two-tone letter.
    • Infill: the domes are solid shapes, so 10–15% infill saves filament.
    • Cake toppers: printed plastic is not food-safe by default. Wrap the stake before it touches food.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits.

    Will it fit my printer?

    Choose your printer below the preview. The letters and stands are packed onto as many plates as needed; a single letter bigger than the bed is flagged, so lower the letter height.

    Do I need supports?

    No. Every piece has a flat back and a dome on top, and the stands print with the slot facing up.

    Are they hollow like real balloons?

    No, they are solid prints that look inflated. They don’t float, and low infill keeps them light.

    Can I sell letters I print?

    The designs you make are yours. The typefaces are open-licensed, which allows making physical products. Small letters and knots are small parts, so check toy-safety rules before selling for children, and don’t claim food safety for cake toppers.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-10. Community posts are one maker's experience, not a specification.

    1. Color change Prusa Research
    2. Modeling with 3D printing in mind Prusa Research
    3. Food-safe FDM printing Prusa Research
    4. Small Parts Ban and Choking Hazard Labeling U.S. Consumer Product Safety Commission
    5. SIL Open Font License SIL International