Free generator · Runs in your browser

Can holder generator Your name on every drink.

Make a can holder for standard, slim or tall cans, a coffee cup sleeve or an ice-cream pint holder. Wrap a name around it, add ribs, a honeycomb or waves for grip, and a handle if you like.

  • Private by designNothing leaves this device
  • Cans, cups, pintsPublished can sizes or your own
  • No supportsPrints upright
  • Ready to sliceSTL or 3MF

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

What it holds

Sleeve for

Body diameter × height, from can makers’ published sizes. Cans vary a little; print the fit-test ring first if you want it snug.

Measure across the body, not the rim.

Measure your own cup: these are example values, not a standard size.

Across the outside of the rim.

50 mm
25 mm

Where the sleeve’s lower edge sits on the cup. The sleeve wedges on the taper there.

Measure your pint tub: these are example values, not a standard size.

Across the outside, just under the lid.

Without the lid.

70 %

How much of the tub’s height the holder covers.

For a bottle, jar or glass: measure the part the sleeve will cover.

80 %

How much of the height the holder covers. Leave the top free to drink from.

Off for an open-bottom sleeve that slides on.

Fit and wall

0.6 mm

The gap between the sleeve and the can or cup on each side. More slides on easier; less holds tighter.

2.4 mm

Thicker walls with sparse infill trap more air.

Lets drips out and lets you push the can up from below.

A 10 mm ring with the same inside size, to check the fit in a few minutes before the full print.

Text

A name or a short phrase. It wraps around the front and shrinks to fit if needed.

Typeface
Letters
14 mm
1.0 mm

Engraving never goes deeper than the wall minus 1 mm.

Grip

Grip pattern
8 mm

Rib spacing, cell size or wave spacing.

1.0 mm

A side handle with a finger hole, shaped to print without supports.

A dip in the rim at the back, to grip the can and pull it out.

Colour

Preview

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The method

    How to make a can holder or cup sleeve

    Pick what the sleeve holds. Can sizes come from can makers’ published dimensions; for a coffee cup, an ice-cream tub or anything else, you measure it. The generator follows the taper, adds your clearance and wall, wraps your text around the front and fills the rest with a grip pattern.

    1. Choose a can size, or measure your cup or tub: across the top, across the base and its height.
    2. Set the clearance. Print the 10 mm fit-test ring if you want it exact.
    3. Add a name or phrase, raised or engraved, and a grip pattern.
    4. Download and print it upright, with no supports.

    Sizes

    Can sizes

    CanBody diameterHeightSource
    12 oz / 355 ml standard66 mm122.22 mmCan maker’s page
    12 oz / 355 ml slim58 mm156.59 mmCan maker’s page
    16 oz / 473 ml tall66 mm157.23 mmCan maker’s page
    330 ml standard66 mm115.2 mmCan maker’s page
    250 ml slim53 mm133 mmCan maker’s page
    500 ml tall66 mm168 mmCan maker’s page

    Cans from different makers and countries can differ slightly, so the clearance gives some room. Cups and ice-cream tubs have no single standard size: measure yours.

    Fit

    Clearance, materials and what to expect

    • Clearance: the gap on each side. 0.6 mm suits a rigid PLA or PETG sleeve; less holds tighter but may not slide on. In TPU, 0–0.2 mm stretches over the can for a snug grip.
    • Cone sleeves: a coffee sleeve or pint holder wedges on the taper. More clearance lets it slide further down before it grips.
    • Cold drinks: cans sweat. PETG resists water and humidity, and TPU is flexible, so either suits a can holder. PLA works too; let it dry between uses.
    • Hot drinks: PLA softens and deforms above about 60 °C. Print coffee sleeves in PETG, which copes up to about 80 °C.
    • Insulation: a printed sleeve keeps a drink cold for less time than a foam one. Foam is mostly trapped air, which carries heat far less than solid plastic. A thicker wall with sparse infill helps a little.

    Printing

    Printing tips

    • Upright, no supports: raised letters and patterns have bevelled undersides, the handle climbs at 45° and its finger hole has a pointed top.
    • Crisp letters: use 0.12–0.16 mm layers, and print the outer wall first if your slicer offers it.
    • Two-tone letters: fill engraved text with acrylic paint and wipe the surface.
    • TPU: print slowly, around 20 mm/s, with little or no retraction.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits.

    Will it fit my printer?

    Choose your printer below the preview. A can holder is about 75 mm across and up to 140 mm tall, which fits most printers; a handle adds about 27 mm.

    Will it keep my drink cold?

    A little. A printed sleeve is less insulating than a foam one, because foam is mostly trapped air. It does keep your hand off the cold can and gives a better grip.

    My cup or tub isn’t listed. What do I measure?

    Choose Coffee cup, Ice-cream pint or Custom, then measure the outside diameter at the top and at the bottom, and the height. A ruler held across the top is fine; calipers are better.

    Can I sell sleeves I print?

    The designs you make are yours. The typefaces are open-licensed, which allows making physical products. Don’t print other people’s logos or brand names without permission.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-10. Community posts are one maker's experience, not a specification.

    1. 12 oz / 355 ml standard beverage can Crown Holdings
    2. 12 oz / 355 ml slim beverage can Crown Holdings
    3. 16 oz / 473 ml standard beverage can Crown Holdings
    4. 330 ml standard beverage can Crown Holdings
    5. 250 ml slim beverage can Crown Holdings
    6. 500 ml standard beverage can Crown Holdings
    7. 47.3 cl standard beverage can Canpack
    8. PLA Prusa Research
    9. PETG Prusa Research
    10. Flexible materials Prusa Research
    11. Thermal conductivity of selected materials and gases The Engineering ToolBox
    12. SIL Open Font License SIL International