Free generator · Runs in your browser

Geometric lattice ornament generator Light, open, 3D.

Make wireframe polyhedra, geodesic and Voronoi spheres, stars, leaf lattices and spiral cages as ornaments or lamp shades, printed in one piece, as two halves that snap together, or as a flat-pack kit.

  • Private by designNothing leaves this device
  • Twelve latticesFrom cubes to Voronoi cells
  • Honest about supportsOr none, as a flat-pack kit
  • Ready to sliceClean, sealed struts

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Lattice

3

How many times each triangle of an icosahedron is split. 1 is the icosahedron itself; 4 makes 480 struts.

Points
1.70 ×

How far the points reach, as a multiple of the inner ball.

32
60 %

100% makes cells of nearly the same size; lower is more organic.

7

Each number shuffles the cells into a new layout.

5
8
6
2
70 %
Shape
10
140 °

How far each rib turns from bottom to top.

A second set of ribs turns the other way; they meet in diamond joints.

1

Horizontal hoops that tie the ribs together. A lantern always has one at each end.

Struts

80 mm

The widest or tallest measurement, joint balls included, without the loop.

2.4 mm

At least three nozzle widths (1.2 mm on a 0.4 mm nozzle) keeps struts sturdy.

1.8 ×

As a multiple of the strut thickness. Balls never grow past half the shortest strut.

Bends each strut along the ball’s surface for a rounder look. Flat-pack kits always use straight struts.

Print

Print it as

Printed whole, a lattice needs supports under its flatter struts. The tips below the preview count them.

Bottom
2.0 mm

A deeper cut gives a bigger flat footprint.

A flat ring that joins the cut struts, so it stands firmly and sticks to the bed.

Cut at the middle. Each half prints on its cut face; the top half’s lip snaps into the bottom half’s ring.

Flat struts and slotted hubs that print with no supports. Each hub pushes onto its struts from outside. For straight-strut lattices only.

0.20 mm

Gap per side in the joints. Raise it if parts are too tight on your printer; lower it if they are loose.

Top of the ornament

Extras

Needs a joint at the very top. Lanterns are open at the top: hang them by a ribbon.

5.0 mm
Inside
14 mm

A faceted bead with a hole for thread, printed separately. It shrinks if it would not fit inside.

Battery LED tealights only, never a flame. One piece only: the bottom is cut open so the shade sits over the tealight.

Measure yours. Many are about 38 mm across.

Measure to the tip of the plastic flame.

Preview

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The method

    How to make a lattice ornament

    Choose a lattice, set its size and strut thickness, then choose how to print it. Every strut is built as its own closed tube that ends inside the joint balls, so the file is clean for any slicer.

    1. Pick a lattice: a wireframe solid, a geodesic or Voronoi sphere, a star, or a diamond, leaf or spiral cage.
    2. Set the size and struts. Thicker struts and bigger balls are sturdier.
    3. Choose how to print it: one piece, two halves, or a flat-pack kit.
    4. Add a loop, a bead or a tealight opening, then download.

    Printing

    One piece, two halves or a flat-pack kit

    Print asSupportsBest forAssembly
    One pieceYes, under the flatter struts (the tips count them)Small ornaments, a lamp shade cut flat on the bedNone
    Two halvesFewer: each half prints on its flat cut faceOrnaments with a bead insidePress the halves together until the lip snaps in
    Flat-pack kitNoneBig polyhedra and geodesic spheresPush each hub onto its struts; a drop of glue makes it permanent

    Lattices

    The lattices

    LatticeJointsStruts
    Tetrahedron46
    Cube812
    Octahedron612
    Dodecahedron2030
    Icosahedron1230
    Truncated icosahedron6090
    Geodesic sphere, frequency 2 / 3 / 442 / 92 / 162120 / 270 / 480
    Star, 20 points3290
    Voronoi sphere2 × cells − 43 × cells − 6

    Printing

    Printing tips

    • Supports: for one-piece lattices use organic (tree) supports from the build plate only, so none grow inside the ball.
    • Struts: keep them at least three nozzle widths thick; 2 mm or more on a 0.4 mm nozzle is a good start.
    • Halves: print a small one first to check the snap. Change the fit clearance if it is too tight or too loose.
    • Flat-pack: parts with the same letter are the same shape. Glue makes the kit permanent.
    • Light: use battery LED tealights only. Printed plastic softens and burns near a flame.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits.

    Will it fit my printer?

    Choose your printer below the preview. A flat-pack kit fills as many plates as it needs; for one piece or two halves, lower the size if it is too big.

    Why does a one-piece lattice need supports?

    A printer builds each layer on the one below. Struts flatter than about 45° from the bed, and joints where every strut climbs away, start over thin air. Two halves or a flat-pack kit avoid most or all of that.

    Can I put a light inside?

    Only a battery LED tealight. Never use a candle or any flame: printed plastic softens, melts and can burn.

    Can I sell ornaments I print?

    The designs you make are yours, and these are classic geometric shapes anyone may make. Beads and kit parts are small, so check toy-safety rules before selling for children.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-10. Community posts are one maker's experience, not a specification.

    1. Support material Prusa Research
    2. Tealight: size of a typical tealight Wikipedia
    3. Geodesic polyhedron Wikipedia
    4. Truncated icosahedron Wikipedia
    5. Spherical Voronoi diagram (Voronoi diagram) Wikipedia