Free generator · Runs in your browser

LED neon sign generator Your word in light.

Make a printed channel for LED neon flex in the shape of a word, a heart, a bolt or your own line drawing, sized to your strip, with a length readout and parts that fit your printer.

  • Private by designNothing leaves this device
  • Single-line lettersScript, block, shapes or SVG
  • Sized to your stripWidth, bends and cut marks
  • Ready to sliceSTL and 3MF files

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Design

Make it from

Up to 3 lines. Letters, numbers and . , ! ? - : + / ' are drawn as single lines. Type ♥ ★ ⚡ or → for a symbol.

Letters

Joined script links lowercase letters along the baseline into one connected channel.

70 mm

Height of a capital. Bigger letters allow gentler bends.

0 mm
0 °
Symbol side

A rounded rectangle of strip around everything, as its own run.

Shape
160 mm

Showing a sample spiral until you choose a file.

Drawing pad

Draw with a mouse, finger or pen. Each line you draw is one run of strip. The pad needs a pointer: without one, choose a shape or an SVG file instead.

170 mm

The longer side of the drawing.

Strip

Fills in a starting point. Measure your strip with calipers: strips differ between makers.

Kind

Across the lit face.

From the back to the lit face.

0.40 mm

Added to the strip width: the channel’s inside width.

8.0 mm

How much of the strip the walls hold. Neon flex usually stands out of the channel.

From your strip’s data sheet. Tighter bends are marked.

Printed on the strip.

From the data sheet.

Channel

1.6 mm
Hold the strip with
40 mm

Short lips that lean in over the strip, this far apart.

0.6 mm

Thinner is brighter; thicker hides the LED dots.

Off: the channel is open at the back, with a rung every 25 mm.

Through the back, for the feed wires.

4.0 mm

Never wider than the channel.

Backboard

Backboard
10 mm
3.0 mm
12 mm

Fills the middle of letters like O and the inside of a heart.

With no backboard, tie bars join the pieces into one part.

Hang it with

Measure your screw head.

The stand needs a rectangle or rounded backboard.

Bigger than the bed
Joints

Pick your printer below the preview: parts are cut and packed for its bed.

Look

Preview

Only in the preview: the strip is never in the download.

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    Read first

    Low voltage only

    • Use low-voltage LED strip (5, 12 or 24 V) with a power supply listed for it. Never wire mains voltage into a printed sign, and never use glass neon.
    • Plastic softens with heat. PLA softens at about 60 °C. Run the sign for an hour and touch the strip: if it is warm, print in PETG.
    • Size the supply above the power the readout gives, and protect the wiring.
    • Keep the cut ends sealed with the end caps that come with the strip.

    We make no electrical, fire or compliance claims for printed signs.

    The method

    How to make an LED neon sign

    A neon tube follows a single line, not the outline of a letter. This generator draws every letter as strokes, then builds a channel along each stroke that your strip presses into.

    1. Design: type a word, pick a shape, upload an SVG line drawing or draw one.
    2. Strip: measure your strip and enter its minimum bend radius from the data sheet.
    3. Check: red rings mark bends that are too tight or lines that cross. Make the design bigger until they go.
    4. Print lying on its back, with no supports. Large signs come as numbered parts.
    5. Fit the strip: cut each piece at the last mark that fits its run, as the advice lists, feed the wire through the hole at the start and press the strip in.

    Sizes

    What you measure, and what it sets

    You measureIt sets
    Strip widthChannel inside width: the width plus the clearance
    Strip heightHow far the strip stands out (shown in the preview)
    Minimum bend radiusWhere bends are marked as too tight; script letters are rounded to it
    Cut mark spacingHow much strip to buy for each run
    Power per metre and voltageThe power estimate for choosing a supply
    Starting pointWidthHeightChannel depth
    6 × 12 mm neon flex6 mm12 mm8 mm
    8 × 16 mm neon flex8 mm16 mm11 mm
    12 × 20 mm neon flex12 mm20 mm13 mm
    8 mm bare LED strip under a cap8 mm2.5 mm12 mm
    10 mm bare LED strip under a cap10 mm2.5 mm12 mm

    These are starting points, not standards. Neon flex comes in many sizes and stiffnesses, so measure yours. The 6 × 12 mm entry, its 50 mm cut marks and 10 W per metre come from a published side-bend data sheet (see the sources). Published minimum bend radii for 6 × 12 mm side-bend strip range from about 20 mm to 60 mm (see the sources; some sheets give a diameter, which is twice the radius). The starting value of 20 mm matches the lowest of those, so check your own strip’s figure and enter it.

    Runs

    Runs, joints and cut marks

    • A run is one piece of strip. In the joined script, letters link along the baseline into one connected channel: letters that start from the baseline, like i, n and m, carry the strip straight on, and elsewhere one piece ends where the next begins. Capitals, t bars and sharp corners start new runs.
    • Each run needs its own feed: a wire from the supply, or a link from the end of the run before. A wire hole sits at each run end.
    • Strip can only be cut at its marks. The advice rounds each run down to the last mark that fits. The short gap left at the end takes the strip’s end cap; change the size a little if a run lands far from a mark.
    • Joints: where a run meets another line, butt the strip ends together; the channel is continuous.

    Printing

    Printing tips

    • On its back, no supports. The channel walls rise straight up; the clip tabs and lips are short overhangs that print without support.
    • Two colours: the backboard and channel are separate parts in the 3MF. On one nozzle, swap filament at the top of the backboard.
    • Test the fit with a short piece first, and change the clearance by 0.1 mm if the strip is loose or tight.
    • Big signs: parts are numbered on the back. Dry-fit them, then glue the dovetail joints.
    • Bare strip: print the diffuser caps in white or clear filament and press them in over the strip.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits.

    Will it fit my printer?

    Choose your printer below the preview. Signs bigger than its bed are split into keyed parts packed onto its plates.

    Which strip should I buy?

    Low-voltage neon flex that bends sideways (side bend), or bare LED strip with the diffuser caps. Check its width, minimum bend radius and cut marks on the data sheet, and enter them here.

    Can I use it with mains or glass neon?

    No. It is for low-voltage LED strip only, from a power supply listed for it.

    Can I sell what I print?

    The designs you make are yours, and the stroke letters are drawn for this tool. We make no electrical or safety claims, so test anything you sell and don’t promise more than you have tested.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-13. Community posts are one maker's experience, not a specification.

    1. Neon side bend 24 V RGB (FLN2410RGB) SAL
    2. Neon LED 6x12 mm DC12V flexible strip (bend radius 20 mm or more) LedStripStar
    3. LDN0612 LED neon light (minimum bending diameter 60 mm) Myledy
    4. LED Neon Signs with NeoPixels Adafruit Learning System
    5. PLA Prusa Knowledge Base
    6. PETG Prusa Knowledge Base