The method
How the cost is worked out
The calculator adds up everything one successful print uses, then divides by the parts on the plate.
| Cost | How it’s worked out |
|---|---|
| Filament | Grams used ÷ spool weight × spool price, for each filament |
| Electricity | Average watts ÷ 1,000 × print hours × price per kWh |
| Printer wear | Print hours × (printer price ÷ its working hours + upkeep per hour) |
| Labour | Set-up minutes per print, plus finishing minutes per part, at your hourly rate |
| Extras | Consumables per print, plus parts and packaging per part |
| Failed prints | The failure allowance explained below |
With the starting values (45 g of PLA from a $20.00 1 kg spool, 3 hours at 105 W and $0.182 per kWh, 15 minutes of your time at $20.00 an hour), one part costs $6.62. Filament is only $0.90 of that. Your time is usually the largest cost of a small print, which is why selling prices are often several times the filament cost.
Failed prints
Why failures cost more than you’d think
If a share f of prints fail, every good print needs f ÷ (1 − f) failed attempts on average: 0.05 at 5%, 0.25 at 20%, 1 at 50%. A failed print rarely runs to the end, so the calculator counts only the share it got through of the filament, power and printer time. You still pay again for setting up the print and its consumables. Finishing and per-part extras only apply to good parts.
Halving a 10% failure rate saves more than most filament discounts. Calibrate first-layer height and flow before a long batch, and dry hygroscopic filament.
Electricity
How much power a 3D printer uses
A printer draws the most while the bed and nozzle heat up, then much less while it holds temperature. Use the average while printing, not the power supply’s rating, which can be several times higher.
| Printer | Average power | Conditions | Source |
|---|---|---|---|
| Bambu Lab A1 mini | 80 W | PLA (PETG 75 W) | Bambu Lab Wiki |
| Bambu Lab A1 | 95 W | PLA (ABS 200 W) | Bambu Lab Wiki |
| Bambu Lab P1S | 105 W | PLA (ABS 140 W) | Bambu Lab Wiki |
| Bambu Lab P1P | 110 W | PLA (ABS 170 W) | Bambu Lab Wiki |
| Bambu Lab X1 Carbon | 105 W | PLA (ABS 150 W) | Bambu Lab Wiki |
| Bambu Lab P2S | 200 W | PLA, steady state | Bambu Lab Wiki |
| Bambu Lab H2D | 197 W | PLA (PETG 150 W, PC 395 W) | Bambu Lab Wiki |
| Original Prusa MK4S | 80 W | PLA at 26 °C room temperature (ABS 120 W) | Prusa Research |
| Original Prusa MK series | 80 W | PLA at 26 °C room temperature (ABS 120 W) | Prusa Research |
| Prusa CORE One+ | 90 W | PLA (ABS 110 W) | Prusa Research |
| Prusa XL+ single-tool | 235 W | PETG | Prusa Research |
Bed temperature, room temperature and an enclosure change these figures. A plug-in power meter between the printer and the socket shows your own average over a whole print.
Electricity prices
Average electricity prices
| Region | Price per kWh | Period | Source |
|---|---|---|---|
| United States | $0.182 | August 2026, residential average (preliminary) | U.S. Energy Information Administration |
| Great Britain | £0.263 | 1 Oct–31 Dec 2026 price cap, Direct Debit, regional average | Ofgem |
| European Union | €0.283 | First half of 2026, households using 2,500–5,000 kWh a year, taxes included | Eurostat |
Prices vary widely by supplier, tariff and time of day. Use the unit rate on your own bill when you have it.
Selling
Pricing a print to sell
Start from the full cost per part, add a markup for profit, then cover the marketplace’s fees. The calculator solves for the price that leaves your markup after fees: price = (cost × (1 + markup) + fixed fee + fee% × shipping) ÷ (1 − fee%).
| Marketplace | Fees counted | Source |
|---|---|---|
| Etsy (US seller) | $0.20 listing fee for each sale, 6.5% transaction fee, and 3% + $0.25 payment processing, on the price plus shipping. Offsite Ads (12–15%) are left out. | Etsy Help |
| eBay (US, most categories) | 13.6% final value fee on the total sale, plus $0.40 per order ($0.30 for orders of $10 or less). | eBay |
- Fees change. They were checked on 2026-11-08. Check the marketplace’s own fee page before you set prices.
- Not included: sales tax or VAT, advertising, currency conversion and postage itself.
- Selling models you didn’t design? Check the model’s licence first. Many free models don’t allow commercial use.
Lower the cost
Five ways to make prints cheaper
- Fill the plate. Set-up time is shared by every part on it.
- Cut the failure rate with a calibrated first layer, dry filament and a clean build plate.
- Use fewer walls and less infill on parts that don’t carry load. Infill above 20% rarely adds useful strength.
- Orient for fewer supports. Supports are filament and finishing time you throw away.
- Buy larger spools of the colours you use most. The price per kilogram usually falls.
Questions, answered
Is anything uploaded?
No. The numbers are worked out in your browser, and a G-code file is read on your device. Your settings are remembered in this browser only.
Where do I find the grams and print time?
Your slicer shows both after slicing: PrusaSlicer and Orca Slicer in the sliced-info panel, Bambu Studio in the plate summary, and Cura at the bottom right. Or open the G-code file here and they are filled in for you.
Why is the time from my G-code marked as an estimate?
Most slicers write their own time estimate into the file. When a file doesn’t have one, the calculator adds up each move’s distance divided by its speed. That ignores acceleration, so the real print usually takes longer.
Should I charge for my time on a hobby print?
If you’re only printing for yourself, set your hourly rate to 0. If you sell prints, count it: it’s often the largest cost.
Does it convert currencies?
No. Every amount uses the currency you choose, so enter prices in that currency.
Sources
Print advice is a starting point drawn from these references, checked on 2026-11-08. Community posts are one maker's experience, not a specification.
- Bambu Lab printer and AMS power parameters Bambu Lab Wiki
- Original Prusa MK4S 3D printer kit Prusa Research
- FAQ: Frequently asked questions Prusa Research
- Prusa CORE One+ (Gen 2) assembly kit Prusa Research
- Prusa XL+ Single-Tool Prusa Research
- Electric Power Monthly, Table 5.6.A: average price of electricity by end-use sector U.S. Energy Information Administration
- Changes to energy price cap between 1 October and 31 December 2026 Ofgem
- Electricity price statistics Eurostat
- What are the fees and taxes for selling on Etsy? Etsy Help
- Selling fees eBay
- What are payment processing fees for selling on Etsy? Etsy Help