Free generator · Runs in your browser

Holder grid generator Everything in its place.

Make a holder for batteries, SD cards, USB sticks, hex bits, drill bits, hex keys or sockets. Mix up to four items, add labels, and stand it on a desk, in a Gridfinity drawer or on the wall.

  • Private by designNothing leaves this device
  • Sized for real itemsPublished battery, card and tool sizes
  • Fits your drawerFreestanding, Gridfinity or wall
  • Ready to sliceSTL, 3MF and per-colour files

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Items

12
12
2
6

Choose up to four. Each gets its own row; shorter items go at the front.

Custom item sizes
20.0 mm
30.0 mm
5.0 mm
40 mm

How tall the item stands. The pocket holds the share you set under Layout.

Layout

Base
150 mm

Items fill rows across this width. The depth follows from how many you hold.

3 units

1 unit = 42 mm. The depth rounds up to whole units.

A back plate with two countersunk holes for 4 mm screws rises above the holder.

Every row the same height. Off, each row is only as tall as it needs, which saves filament.

Fit

40 %

How much of each battery or card sits in its pocket. Less is easier to grab; more is steadier.

1.6 mm
0.30 mm

Added all round each item. Raise it if things are tight.

22 mm

Centre to centre, for socket rails. Set it a little over your widest socket.

Labels

Item names in front of each row, and sizes under every drill bit, hex key and socket.

Separate them with |, such as 8 | 10 | 12 | 13. One post per size.

Typeface
0.6 mm

Colours

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The method

    How the holder grid works

    Pick up to four things to hold. Each gets a row of pockets sized from its published dimensions plus the clearance you set, packed as tightly as your wall thickness allows. Rows wrap to fit the width, shorter items go at the front, and each row is only as tall as its deepest pocket, so the holder uses as little filament as it can.

    1. Choose the items and how many of each.
    2. Pick a base: freestanding, Gridfinity feet, or a wall plate.
    3. Set how deep the pockets hold, and the clearance.
    4. Print it as laid out, with no supports.

    Sizes

    Item sizes used

    ItemNominal size
    AAAA battery8.3 mm across × 42.5 mm
    AAA battery10.5 mm across × 44.5 mm
    AA battery14.5 mm across × 50.5 mm
    C battery26.2 mm across × 50 mm
    D battery34.2 mm across × 61.5 mm
    9 V battery26.5 × 17.5 mm, 48.5 mm tall
    CR123A cell17 mm across × 34.5 mm
    18650 cell18 mm across × 65 mm
    21700 cell21 mm across × 70 mm
    26650 cell26 mm across × 65 mm
    CR2032 coin cell20 × 3.2 mm, 20 mm tall
    CR2025 coin cell20 × 2.5 mm, 20 mm tall
    CR2016 coin cell20 × 1.6 mm, 20 mm tall
    LR44 button cell11.6 × 5.4 mm, 11.6 mm tall
    SD card24 × 2.1 mm, 32 mm tall
    microSD card11 × 1 mm, 15 mm tall
    CompactFlash card36 × 3.3 mm, 43 mm tall
    USB-A stick12 × 4.5 mm, 11.75 mm tall
    USB-C stick8.25 × 2.4 mm, 6.51 mm tall
    ¼″ hex bit, 25 mm6.35 mm across flats
    ¼″ hex power bit, 50 mm6.35 mm across flats

    Coin cells, cards and 9 V batteries stand on edge in slots. USB pockets fit the metal plug only, so the stick rests on the holder. Cells with protection circuits can be longer or a little wider than the bare size; raise the clearance if one is tight.

    Tool sets

    Drill bits, hex keys and sockets

    Sets get one pocket per size, labelled underneath: metric drill bits from 1 to 10 mm in 0.5 mm steps or 1 to 13 mm, inch drill bits from 1/16″ in 1/64″ steps, and hex keys in the standard metric and inch sizes. Bigger sizes get deeper pockets.

    Socket rails have a square post for each socket: 6.35 mm (¼″), 9.53 mm (⅜″) or 12.7 mm (½″), less the clearance. Type your socket sizes to label each post, and set the spacing a little wider than your biggest socket.

    Printing

    Printing tips

    • Orientation: as laid out, flat side down. Pockets print as straight walls, so no supports.
    • Infill: 10–15% is plenty; the walls between pockets do the work.
    • Labels in a second colour: add a colour change at the top of each row (the advice lists the heights), or switch on Even top for one change.
    • Tight fit? Raise the clearance by 0.1 mm. Small holes print a little undersize on most printers.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits.

    Will it fit my Gridfinity baseplate?

    Yes. On Gridfinity feet, the holder is a whole number of 42 mm units and uses the standard foot, so it drops into any Gridfinity baseplate.

    Can I mix batteries and cards?

    Yes. Choose up to four items. Each gets its own row with its own label.

    Are these sizes exact?

    They’re the published nominal sizes. Real batteries and cards vary a little by brand, which is what the clearance is for. Print a small holder first if you need a snug fit.

    Is it safe for children?

    Keep coin and button cells away from children. Swallowed button batteries can cause serious internal burns within hours.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-09. Community posts are one maker's experience, not a specification.

    1. List of battery sizes Wikipedia
    2. SD card: physical sizes Wikipedia
    3. CompactFlash Wikipedia
    4. USB hardware: connector dimensions Wikipedia
    5. Socket wrench: square drive sizes Wikipedia
    6. Hex key: standard sizes (ISO 2936, ASME B18.3) Wikipedia