Free generator · Runs in your browser

Spice rack and kitchen organizer generator Sized to your jars.

Make a spice rack that fits your jars and your cupboard: steps for a shelf, an insert for a drawer, a wall or door rack, or a turntable. Plus napkin holders, pot lid racks, utensil caddies, sponge holders and jar labels.

  • Private by designNothing leaves this device
  • Eleven organizersRacks, holders and labels
  • No supportsLaid out the way it prints
  • Fits your printerSplit into sections that lock

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Organizer

Make
Spice rack

Steps for a cabinet shelf, so the back row stands higher than the front. Long racks come in sections that lock together with dovetails.

Rows of jars lying at an angle, lids to the front, sized to the inside of your drawer.

Shelves with a rail across the front, screwed to the wall. Printed on its side, so it needs no supports.

Hangs over the top of a cabinet door on two hooks, with no screws.

A turntable: a top with jar pockets turns on a ring of balls in a printed groove.

Sizes

48.0 mm

Measure your jars across the widest part, lid included. Jars differ a lot, so measure rather than guess.

100 mm

Measure your tallest jar, lid on.

3
4
30 mm

How much higher each row stands than the one in front.

380 mm

Measure inside the drawer, wall to wall. The insert is 2 mm smaller so it drops in.

450 mm
100 mm

From the drawer floor to the underside of the cabinet above. Used to check the jars clear it.

20 °

Steeper shows more of each lid but needs a deeper drawer.

2
4

Holes are 0.5 mm wider than the screw, with a 90° countersink for the head.

19.0 mm

Measure the door at its top edge.

3.0 mm

The hook strap is 0.6 mm thinner than this gap, so the door still closes.

250 mm

Shrinks to fit the bed of the printer you choose below the preview.

6.0 mm

Measure your balls. Airsoft pellets are usually about 6 mm; steel bearing balls also work.

0.40 mm

How much wider the groove is than a ball.

10 mm
Style
165 mm

Measure a folded napkin.

165 mm
35 mm

How thick the pile of napkins you want to hold is. The upright holder is 4 mm wider.

Cut-out

Raised letters on the front. Pick a typeface under Labels and text.

6
30 mm

Lay the lid on a table and measure from the table to the top of the knob.

280 mm

Sets how tall and deep the rack is.

2.0 mm

Added to every jar pocket and lid slot, so things slide in easily.

Style
100 mm
140 mm

About two thirds of your longest utensil.

Compartments
3
70 mm

Measure your sponge or brush. The holder is 4 mm bigger inside.

110 mm
30 mm
110 mm
200 mm

Check your printer’s height limit.

60 mm
Shape
40 mm

Measure the top of a jar lid and take off a few millimetres.

50 mm
20 mm
1.6 mm

Labels and text

Names are raised on the front rail (or the step under each jar), in the order of the list: front row first, left to right.

For this rack, make jar labels for the lids instead: choose Jar labels at the top.

One per line, up to 48.

Typeface

This organizer has no text.

Colour

Colour
Preview

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The method

    How to make a spice rack that fits your jars

    Measure one jar and the space it goes in, and the generator sizes every pocket, step and shelf to match. Long racks are split to fit your printer.

    1. Measure a jar across its widest part and from the base to the top of the lid.
    2. Pick a rack: steps for a cabinet shelf, an insert for a drawer, shelves for a wall or a door, or a turntable.
    3. Measure the space: the drawer’s inside, the door’s thickness or the cabinet shelf.
    4. Pick your printer below the preview, then download. Each section is its own object.

    Options

    What it makes

    OrganizerSized byPrints
    Cabinet step rackJar diameter, 2–4 stepsFlat; sections lock with dovetails
    In-drawer insertDrawer inside width and depthOn its side, in pieces that sit side by side
    Wall rackJars per shelf, shelvesOn its side; modules screw on one above another
    Door rackDoor thickness and the gap above itOn its side, in one piece
    TurntableDiameter and ball sizeBase flat, top upside down
    Napkin holderFolded napkin size and stackFlat
    Pot lid rackLid thickness and diameterFlat; sections lock with dovetails
    Utensil caddyCup diameter and heightUpright
    Sponge holderSponge sizeFlat
    Bag dispenserTube sizeUpright
    Jar labelsA list of namesFlat, as a batch

    Printing

    Printing and kitchen tips

    • Near the stove: PLA gets soft and deforms above about 60 °C. Keep PLA racks away from the hob and oven, or print in PETG, which suits use below about 80 °C.
    • Food contact: the layer lines of any print can hold bacteria, so jars should be closed and nothing should touch food directly. Wash holders and caddies by hand in warm, not hot, water; PETG is the better choice for anything that gets wet.
    • Keep jars dry: let jars and the rack dry before putting spices back, and keep the turntable’s ball race dry.
    • Infill: step racks and lid rack bases are solid shapes; 10–15% infill keeps them light and strong.
    • Turntable: print the top upside down as laid out. Fill the groove with balls, leaving a gap of about one ball, then lower the top on.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits.

    Will it fit my printer?

    Choose your printer below the preview. Step racks, lid racks, drawer inserts and wall racks split into sections that fit its bed; the turntable shrinks to fit. The preview “Laid out to print” shows every plate.

    Can I sell what I print?

    The designs you make are yours. The typefaces are open-licensed, which allows making physical products. Anything meant for food needs its own checks before you sell it: we make no food-safety claims.

    Are prints food safe?

    Not as printed. Layer lines can hold bacteria, so use these to hold closed jars, utensils and sponges, not loose food. A food-safe coating helps, and a stainless-steel nozzle avoids lead from brass nozzles.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-12. Community posts are one maker's experience, not a specification.

    1. PLA Prusa Research
    2. PETG Prusa Research
    3. Airsoft pellets Wikipedia
    4. DIN 7997: cross-recessed countersunk head wood screws, dimensions fasten.it
    5. SIL Open Font License SIL International