Free generator · Runs in your browser

Prop hilt generator Build it section by section.

Stack an emitter, neck, switch section, grip, spacers and a pommel into a sci-fi prop hilt, joined with printable threads, with a hollow bore sized to your own parts. Or make a fantasy sword grip with a crossguard and pommel.

  • Private by designNothing leaves this device
  • Section builderAdd, remove and reorder
  • No supportsEvery section prints upright
  • Ready to sliceEach section its own object

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Hilt

Make
Sections, emitter end first

The first section is the emitter end and the last is the pommel end. Change each section’s style, length and diameter, and use Up and Down to change the order.

  1. Emitter
  2. Neck collar
  3. Switch section
  4. Grip
  5. Spacer ring
  6. Pommel

6 sections of up to 12.

35.0 mm

Every section uses this unless you give it its own. Measure across your hand’s grip, or a hilt you like holding.

110 mm

About one hand width per hand, plus a little.

32.0 mm

Across the wide side; the grip is slightly oval.

Grip
Crossguard
170 mm

Tip to tip. A round disc guard is half this across.

14 mm
Pommel
44 mm
32 mm

Joints and inside

Joints
0.20 mm

0.2 mm suits printed threads on most printers. Raise it if joints bind.

0.10 mm

Smaller is tighter. Print one joint to test before the whole hilt.

10 mm

How far each spigot goes into the next section. Longer is stronger.

A bore through every section, for wiring, a light or a battery you measure yourself.

Measure the widest part that must slide through, and add 0.5–1 mm. It is limited so walls and threads stay strong.

Measure the body of your button or switch with calipers. Seats are 0.3 mm larger.

1.5 mm
3.0 mm
Blade fits by

Measure your blade’s tang, or the flat bar you use as one.

Measure your dowel or rod with calipers.

0.20 mm

Leave room for glue; 0.2 mm is a snug slide on most printers.

Colours

Preview

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The method

    How to make a prop hilt from sections

    Build a hilt from sections in order, from the emitter end to the pommel end. Each section is turned like a part on a lathe, and the sections join with threads, push fits or bayonet lugs. Print each one upright, then screw them together.

    1. Pick the sections and put them in order. Give each one a style and a length.
    2. Set the diameter for the whole hilt, or give a section its own.
    3. Choose the joints and, for a hollow hilt, measure what goes inside and enter the bore.
    4. Download and print. Every section is its own object, so each can take its own colour.

    For a fantasy sword, switch to Fantasy sword grip: a grip, a crossguard and a pommel slide onto a slot sized to your blade’s tang or a dowel.

    Sections

    The sections

    SectionStylesLengthWhat it is
    EmitterCrown, Vented shroud, Flared tip24–70 mmAn end piece with a thin cup at the top
    Neck collarRings, Waisted, Plain band14–40 mmA short collar between the emitter and the switch
    Switch sectionOne button, Two buttons, Button and window30–90 mmA flat with button seats; a window on the back
    GripRibs, Rings, Knurl, T-track look, Cord wrap40–220 mmThe long section you hold
    Spacer ringPlain, Grooved, Bevelled4–20 mmA ring that slides over a joint between two sections
    PommelCap, Lanyard ring, Flared end, Curved and angled18–60 mmThe other end; it unscrews for access

    An emitter or pommel placed between two sections is built without its end. Spacer rings always sit between two sections.

    Joints

    Joints and clearances

    JointHow it holdsClearance to start with
    ThreadA coarse 60° thread with a 2.5 mm pitch, cut as large as the wall allows0.2 mm per side
    Push fitA smooth spigot in a socket; glue it for good0.1 mm per side
    BayonetLugs on the spigot lock into L-shaped slots with a short turn0.1 mm per side

    Every spigot has a 45° shoulder and every socket a matching 45° mouth, so sections print without supports whichever way up they stand.

    Printing

    Printing and finishing tips

    • Orientation: print as laid out: upright, socket down. The pommel-end section stands on its spigot; add a brim.
    • Material: PETG is tougher than PLA and copes better with heat; PLA is fine for a display piece.
    • Threads: 0.2 mm layers or finer and 3 or more walls make joints strong.
    • Finish: sand from 220 to 400 grit, prime with a filler primer and paint. Metallic paint over gloss black looks most like metal.
    • Inside: the bore is your measurement. Test-fit what goes inside in a short section before printing the rest.

    Safety

    Props only

    These hilts are costume props. They are not for combat, sparring or striking anything, and printed parts can crack. Event weapon policies vary, so check your event’s prop rules before you bring one. Small parts are not for children under 3.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits.

    Will it fit my printer?

    Choose your printer below the preview. Sections print upright, so the tallest section must fit your printer’s height; the readout shows the plates the sections fill.

    Can I sell hilts I print?

    The designs you make are yours. The shapes here are generic, not copies of any film or game prop. Check your local rules for selling toys and props.

    Can I fit electronics inside?

    The generator only makes the space: a bore of the size you enter and button seats of the size you measure. It does not make or check any electronics. Follow the maker’s instructions for anything you fit.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-12. Community posts are one maker's experience, not a specification.

    1. ISO metric screw thread Wikipedia
    2. 3D printing threads Snapmaker
    3. Modeling with 3D printing in mind Prusa Research
    4. PETG Prusa Research
    5. Small parts for toys and children’s products US Consumer Product Safety Commission