Free generator · Runs in your browser

Dice tower generator Every roll, fair and square.

Make a dice tower and tray sized to your dice: one piece that prints upright with no supports, or flat-pack panels that slot together. Add battlements, magnets and your name.

  • Private by designNothing leaves this device
  • Two buildsOne piece or flat-pack
  • No supports45° baffles and a pointed exit
  • Ready to sliceEvery piece named and packed

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Tower

Make
Build

Prints upright in one go, with no supports.

Panels print flat and quickly, fit small beds, and slot together without glue.

16 mm

The size your dice set is sold as, which is the d6’s edge. Standard sets are 16 mm; chunky sets 20–25 mm.

Room inside
3

More baffles tumble the dice more, and make the tower taller.

2.8 mm
Top

Lettering

A name, a party name or a motto, across the front above the exit. Leave it blank for none.

Style
Typeface
12 mm

Long words shrink to fit the front.

0.8 mm

Tray

Rolling area
18 mm

Disc magnets, diameter × thickness. Pockets go in the tower’s base and the tray floor so the two snap together.

One piece to print. Larger, but nothing to lose.

Fit

0.15 mm

Gap between each tab and its slot, per side. Raise it if the panels are tight.

One-piece towers have no joints to fit. Switch to Flat-pack for slot clearance.

Colours

Preview

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The method

    How the dice tower works

    Dice dropped in the top bounce off a stack of sloping baffles, alternately from the front and back walls, then roll down a floor ramp and out of the exit into the tray. Every gap is worked out from your dice size, so a tumbling d6 (about 1.7 times its edge from corner to corner) always has room to pass.

    1. Set your dice size and how many baffles.
    2. Pick one piece or flat-pack.
    3. Add lettering, battlements and magnets if you like.
    4. Download and print. Every piece is laid out flat or upright, ready to slice.

    Builds

    One piece or flat-pack?

    ComparedOne pieceFlat-pack
    PrintsUpright, as one tall partFlat panels, quickly
    SupportsNone: 45° baffles and a pointed exitNone
    PrinterNeeds the tower’s height in ZFits smaller beds; pieces spread over plates
    AssemblyNoneSlots together; a drop of glue optional
    Two-colour letteringPaint, or a multi-material printerA colour change at the panel’s thickness

    Dice

    Choosing the dice size

    Dice sets are usually sold by the size of the d6: a “16 mm” set has a 16 mm cube, and the other dice are sized to match it. Standard sets run from about 14 to 16 mm, so 16 mm suits most tables. Sizes vary between makers, so measure your largest die if in doubt, and choose Roomy for chunky, sharp-edged or metal dice.

    Printing

    Printing tips

    • Layers: 0.2 mm is fine; the baffles are 45° slopes that print cleanly.
    • Walls: 2.8 mm walls are three to four perimeters with a 0.4 mm nozzle, sturdy enough for metal dice.
    • Magnets: pockets are 0.3 mm wider than the magnet; a drop of superglue holds them.
    • Quieter rolls: line the tray with felt or cork.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits.

    Do I need supports?

    No. One-piece towers print upright with 45° baffles and a pointed exit; flat-pack panels print flat.

    Will my dice jam?

    The gaps between baffles are about 1.75 times the dice size and the passages under them about 1.9 times, more than the corner-to-corner size of a tumbling d6. If you use oversized dice, raise the dice size or choose Roomy.

    Can I sell towers I print?

    The designs you make are yours, and the typefaces are open-licensed, which allows making physical products.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-09. Community posts are one maker's experience, not a specification.

    1. Dice sizes: what size is standard? Bryce’s Dice
    2. Measurements of standard polyhedral dice (forum discussion) The Straight Dope Message Board
    3. SIL Open Font License SIL International