Free generator · Runs in your browser

Dungeon tile generator Build the dungeon, square by square.

Draw a dungeon and print it: textured floor tiles on the 1-inch tabletop grid, stone walls with doors and arrow slits, stairs, pillars, a chest and a portcullis, all split to fit your printer with a numbered map.

  • Private by designNothing leaves this device
  • 1-inch gridLines up with battle mats
  • No supportsTiles flat, walls standing
  • Ready to sliceA parts list and a numbered map

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Make

What to make

Click or drag to paint squares. With the keyboard: arrow keys move, Space paints, Shift with an arrow paints as it moves, 1 picks floor, 2 wall, 3 door, F fills, Ctrl+Z undoes. Walls are built along every edge where floor meets wall. A door square needs wall on two opposite sides. Floor at the map’s edge is left open, to join more sections later.

4 squares

Floor is split into pieces at most this many squares each way, and walls at most this long. Pieces also shrink to fit the printer you pick below the preview.

4
Wall piece
2 squares

Corner and T pieces have arms this long.

Openings
Fitting
2

Each is its own piece. Pillar, rubble and pit stand on textured tiles that match your floor.

Floor

A 1.2 mm groove on every 1-inch line, so the squares read at a glance.

5.0 mm

Under the texture. Thicker if you use magnets or clips.

The same seed always lays the same stones, and it is saved in shared links.

Walls

Wall height
8.0 mm

Including the 0.8 mm stone relief on each face. Walls stand in the wall squares, beside the floor.

A hinged door swings on a short length of 1.75 mm filament. A slide-in door drops into grooves from the top, so it lifts out.

Joins

Underneath

Dovetail slots at every square along the edges. Bow-tie clips print with the set and press into two slots to lock neighbours together.

Disc magnets, one near the middle of every edge square. Pockets are 0.3 mm wider and 0.2 mm deeper than the magnet.

Colours

Preview

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    The method

    How to make dungeon tiles

    Draw a room on the map, or make tiles, walls and features one kind at a time. Everything sits on the common tabletop grid of 1-inch squares, so it lines up with battle mats and with miniatures on 25 mm bases.

    1. Draw the dungeon: floor, wall and door squares.
    2. Pick the floor texture and roll a stone layout you like.
    3. Set the walls: height, thickness and doors.
    4. Choose how pieces join: clips, magnets or neither.
    5. Pick your printer below the preview. Pieces split to fit its bed, and the parts list and numbered map show where each goes.

    Scale

    The 1-inch grid and miniature scale

    Battle maps for tabletop role-playing games use squares of one inch (25.4 mm), and each square usually stands for 5 feet in the game. Miniatures sold as 28 mm or 32 mm scale mostly stand on 25 mm round bases, which fit inside one square.

    TileSizeSquares
    1 × 125.4 × 25.4 mm1
    2 × 250.8 × 50.8 mm4
    3 × 376.2 × 76.2 mm9
    4 × 4101.6 × 101.6 mm16
    6 × 6152.4 × 152.4 mm36
    Wall heightAbove the floorGood for
    1 in25.4 mmLow walls that let you see and reach the miniatures
    1.5 in38.1 mmA compromise for busy tables
    2 in50.8 mmFull-height dungeon walls for 28 mm miniatures
    3 in76.2 mmTall halls and 32 mm miniatures

    Printing

    Printing tips

    • No supports: tiles print flat, walls print standing up, and door and window tops bridge.
    • Layer height: 0.2 mm is fine; 0.12–0.16 mm makes the stone edges crisper.
    • Magnets: check the polarity with a neighbour before gluing, and use a drop of superglue in each pocket. Alternate the poles round the edges so any two tiles attract.
    • Clips: they are a snug press fit. If yours are loose or tight, scale the clips by 1 or 2% in the slicer.
    • Hinged doors: slide a short piece of 1.75 mm filament down through the lintel, the door’s barrel and into the sill. A drop of glue in the lintel keeps it there.
    • Painting: prime grey or black, dry-brush a lighter grey over the stones, and wash the mortar lines dark.

    Questions, answered

    Is it free to use?

    Yes. No account, no watermark, no limits.

    Will it fit my printer?

    Choose your printer below the preview. The room builder splits floor and walls into pieces that fit its bed, and everything is laid out on as many plates as needed. A single tile larger than the bed is flagged.

    Do these work with other dungeon tiles?

    They use the common 1-inch grid, so they line up with battle mats and most grid-based terrain. The clips are a generic dovetail of their own and do not fit other clip systems.

    Can I sell tiles I print?

    The designs you make are yours. There are no typefaces or third-party models in them. Magnets and clips are small parts, so check toy-safety rules before selling for children.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-12. Community posts are one maker's experience, not a specification.

    1. Battle grids: one-inch squares Dummies
    2. 24" × 36" double-sided mat, 1" squares Noble Knight Games
    3. Basing guidelines: base size guide Hobby Heaven
    4. Magnet size guide for tabletop bases first4magnets
    5. Color change Prusa Research