Free generator · Runs in your browser

JPG to STL Photos as 3D reliefs.

Drop in a JPG photo and get a 3D relief where brightness becomes height. Add a frame, a stand or a hanging hole, flatten it into bas-relief wall art, and download an STL or 3MF.

  • Private by designPictures stay on this device
  • Three modesRelief, logo or painting
  • Any printerColour from filament swaps
  • Ready to sliceSwap list and 3MF parts

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Picture

Make a

Brightness becomes height: light areas stand up, dark areas sink. Best for portraits, pets and landscapes.

The picture is split into two heights: a plate and a raised logo. Best for logos, drawings and text with strong contrast.

A thin stepped relief printed with several filaments, swapped at set layers. Light through the thin top layers blends the colours into a picture.

Shape and size

Shape

The middle of the picture is used, cropped to a square.

Follows the picture’s transparent background, or else the colour around its edge.

120 mm

The other side follows the picture’s shape, so nothing is stretched.

Detail in the file

Grid spacing in the download: about 0.25, 0.18 or 0.12 mm for a relief. The preview uses a coarser grid. Files stay under 1.5 million triangles.

3.0 mm

Near the top in the middle, with a solid ring round it.

5.0 mm

A separate block with a slot that holds the panel leaning back 15°.

Heights and filaments

0.8 mm

The darkest areas. 0.8 mm or more keeps the panel stiff.

6.0 mm

The brightest areas, and the frame.

Flattens the big light-to-dark shading so the detail stands out, like a carved plaque.

0.70
1.6 mm
1.2 mm
3.0 mm

With the Picture outline shape, the plate follows the logo’s outline this far out.

Splits dark from light where the picture divides most cleanly. Dark parts are raised; Invert raises the light parts.

0.50

Areas darker than this are raised.

4

Each one is a swap during the print. Three or four cover most pictures.

TD (transmission distance) is how many millimetres of a filament it takes to block light. It varies between brands and colours, so measure yours: print a strip of steps 0.08 mm apart, hold it in front of a bright light and note the thinnest step that blocks it. “Fill in” uses one maker’s published values as a start.

Filament 1 · the base
Filament 2
Filament 3
Filament 4
Filament 5
Filament 6
Filament 7
Filament 8
Order and swap heights

Auto prints darkest to lightest and suggests the heights from each filament’s TD. As listed keeps your order. Set by hand uses each filament’s start height, snapped to a layer.

Layers and parts

Slice with exactly this height. 0.08 mm gives the smoothest blends.

A thicker first layer sticks better. It must match your slicer too.

0.48 mm

The solid backing under the picture, and its darkest areas.

1.60 mm

The lightest areas. More height gives more shades, but light filaments need a few TD to look solid.

Match the picture by
Preview
Download as

A part per colour suits multi-material printers (each colour its own object in the 3MF). One body suits one nozzle with colour changes at the listed heights.

A photo relief prints in one colour. For colour, choose Filament painting.

Adjust the picture

Stretches the darkest and lightest tones to use the full height.

0.00
1.00
1.00

Above 1 lifts the shadows; below 1 deepens them.

0.30

Smooths grain and skin while keeping edges sharp.

0.0 mm
0.30

Relief: dark areas stand up. Logo: the light parts are raised. Painting: a negative.

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    JPG to STL

    How JPG to STL works here

    A JPG is a photo with no transparency, so every pixel becomes part of a solid plate. Light areas stand tall and dark areas sit low (or the other way round with Invert).

    Photos look best with clear light and shade. The levels, contrast and sharpen controls in step 2 help a flat or dim picture. Bas-relief squeezes the height range so it reads well on a wall.

    If you want light to shine through the photo instead, the lithophane generator is the better tool. Your photo never leaves this device.

    Other ways in: Image to STL · PNG to STL · Filament painting · Drawing to 3D print.

    The method

    Turn an image into an STL

    Add a PNG, JPG or WebP. The picture is read on your device and turned into a heightmap: every pixel becomes a height. Choose what kind of print you want, set the size, and download an STL or 3MF.

    1. Add a picture, or try a sample.
    2. Choose a mode: photo relief, logo emboss or filament painting.
    3. Pick a shape and size. The aspect ratio is kept, so nothing is stretched.
    4. Adjust the picture until the preview looks right, then download.

    Modes

    Three ways to print a picture

    ModeWhat you getBest for
    Photo reliefA smooth surface: brighter is higher (or invert it). Bas-relief flattens the big shading for wall art.Portraits, pets, landscapes
    Logo embossA plate with the logo raised on it, in one or two coloursLogos, line art, signatures
    Filament paintingA thin stepped relief that shows the picture in colour as filaments are swapped at set layersPhotos and art in colour, on any printer

    A lithophane is the opposite idea: it is lit from behind, so thickness controls how much light gets through. For that, use the lithophane generator. For a vector logo with each colour as its own part, use SVG to STL.

    Filament painting

    How filament painting works

    Thin layers of plastic let some light through. Print a dark filament first, then lighter ones on top, and a pixel’s colour depends on how many layers of each it has: one layer of white over black looks dark grey, ten look nearly white. Each filament’s transmission distance (TD) says how quickly it hides what is below it.

    1. List your filaments with their colours and TD.
    2. The generator sorts them darkest to lightest and suggests the layer for each swap.
    3. Each pixel gets a height: the one whose blended colour is closest to the picture.
    4. Print with the swap list: add a colour change (or pause) at each listed layer, at exactly the layer heights you chose.

    The blend is a model: each layer lets through a share of the light that falls off exponentially with thickness, reaching about 5% at the filament’s TD. Real filaments scatter light too, so print a small test before a big piece.

    TD values

    Transmission distance values

    TD is the thickness at which light is effectively blocked. One filament maker publishes these values for its own colours; other brands differ, sometimes a lot, so measure yours when you can.

    FilamentColourTD
    Black PLA #080A0D0.1 mm
    Grey PLA #8C90990.4 mm
    White PLA #EBF7FF3.2 mm
    Red PLA #E72F1D1.9 mm
    Blue PLA #0037760.3 mm
    Yellow PLA #FFE8004.3 mm
    Matte white PLA #F4EFEB4.1 mm
    Matte light grey PLA #8A8C940.4 mm
    Translucent cyan PLA #08ABFB8 mm
    Translucent magenta PLA #D93B907.8 mm
    Translucent yellow PLA #F9ED3D14 mm

    Measure it: print a strip of steps 0.08 mm apart (the swatch generator adds thickness steps), hold it in front of a bright light, and find the thinnest step you can’t see the light through. That thickness is about the TD.

    Options

    Sizes and options

    OptionRangeNotes
    Size30–300 mmThe longer side; the other follows the picture
    Relief thickness0.4–15 mmThinnest and thickest; 0.8 mm minimum keeps it stiff
    LogoPlate 0.6–6 mm, logo 0.4–6 mmColour change where the logo starts
    Filament painting2–8 filaments, 0.04–0.2 mm layers, 0.6–5 mm tallSwap heights snap to whole layers
    Frame1–15 mm wideAt the full height
    Hanging hole3–10 mmWith a 2.5 mm ring round it
    Detail0.25, 0.18 or 0.12 mm gridFiles capped at 1.5 million triangles

    Printing

    Printing tips

    • Print flat, picture up, with no supports.
    • Filament painting: slice at exactly the layer and first-layer heights you set here, with 100% infill (aligned rectilinear if your slicer has it) so no infill pattern shows through. Common settings are 0.08 mm layers on a 0.16 mm first layer.
    • Swaps: add a colour change or pause at each listed layer. On a multi-material printer, use the 3MF: each filament’s band is its own object.
    • Relief: fine layers (0.08–0.12 mm) keep the detail; side lighting brings it out.
    • Big files: Maximum detail on a large picture can make a file of 50 MB or more. Standard is plenty for most prints.

    Questions, answered

    Relief or lithophane?
    A relief is seen from the front in normal light. A lithophane is thin and is seen with light behind it.
    What layer height should I use?
    0.12 to 0.16 mm keeps the steps between heights fine on a portrait.
    Which way should I print it?
    Flat on its back with the relief facing up, with no supports.
    Is it free to use?

    Yes. No account, no watermark, no limits, and your picture never leaves this device.

    Will it fit my printer?

    Choose your printer below the preview to check. If it is too big, lower the size; the stand prints beside the panel.

    Can I sell prints I make with it?

    The models you make are yours. The picture is the part to check: only use photos and art you made, bought a licence for, or have permission to use. Logos and characters are usually trademarked or copyrighted.

    Which pictures work best?

    For a relief, a well-lit photo with a clear subject and a plain background. For a logo, strong contrast. For filament painting, pictures with clear light and dark areas; busy, noisy photos make bigger files, so raise Denoise.

    PNG or JPG?

    Both work, and so does WebP. A PNG with a transparent background lets you cut the print to the picture’s own outline.

    Why do my colours look different from the preview?

    The preview models how each filament blends from its TD. If your filament’s TD is different, the blend will be too: measure it and enter your value. The layer heights in your slicer must also match the ones here.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-10. Community posts are one maker's experience, not a specification.

    1. HEX codes and transmission distances Polymaker wiki
    2. Wiki: quick cheat sheet (layer heights and infill for filament painting) TailWag Studio, GitHub
    3. Color change Prusa Research
    4. View slicing information (pauses and filament changes) Bambu Lab