Free generator · Runs in your browser

Topographic maps Any place on Earth.

Search for a mountain, a valley or a coastline and get a 3D printable relief map from real elevation data. Set the size, the height scale, a frame and colour bands, and download an STL or 3MF.

  • Your files stay hereGPX trails are read on this device
  • Real elevation dataOpen data for anywhere on Earth
  • No supportsPrints flat on its base
  • Colour-readyBands as parts, with change heights

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Place

Press Enter or Search. Only the words you search for are sent, to the OpenStreetMap place search (Nominatim; data © OpenStreetMap contributors, ODbL).

    Drag the map to move the area, or tap a spot to centre on it. Scroll, pinch or use the buttons to change its size; with the map focused, the arrow keys move it and + and − resize it. The shaded relief is drawn from the same elevation data as the model.

    Getting the preview ready…

    Used for the label and the file name.

    The centre of the map, in decimal degrees: north and east are positive. The area reloads when you leave the field.

    Real-world distance across the map, west to east.

    If one source doesn’t answer, the other is tried.

    Shape and size

    Shape
    0.75 × width
    150 mm

    The terrain itself; a frame or plinth adds to it. Pick your printer below the preview to check it fits.

    4.0 mm
    Edge
    4.0 mm
    4.0 mm
    6 mm
    6.0 mm

    A stepped stand under the map. With a label, the front gets a strip for the text.

    A slot in the back for a screw head, so the map hangs flat with north at the top. Needs a 6 mm base or plinth.

    Relief

    Height exaggeration

    Picks ×1 to ×5 so the relief stands out at this size. ×1 is true to scale.

    1.5 ×

    How many times taller than true scale. Wide areas usually need ×2 or more to look like anything.

    Water

    Everything at or below 0 m becomes a flat sea, with land a step above it.

    Everything at or below this height becomes a flat surface, such as a lake. Look up the lake’s surface height and type it here.

    1.0

    Softens noise and steps in the data. 0 keeps every detail.

    Download detail

    Grid spacing of the downloaded model. The preview is always coarser. Fine files are large; very large maps are capped at about 300,000 grid cells.

    Colours

    Colours

    Rock starts 45% of the way up, snow 80%. Turn off to set real heights in metres.

    Water shows only when the water setting is on and the area has some.

    Trail and label

    GPX trail (optional)

    Trail style
    1.2 mm

    At least two nozzle widths (0.8 mm on a 0.4 mm nozzle).

    On the plinth’s front strip, or on the front edge of the map (needs a base of about 4.5 mm or more).

    Leave empty to use the place name.

    Typeface

    Download

    Building the preview…

    Print it well

      The model is built on this device. To get heights, the page fetches elevation tiles for the area you choose (Terrain Tiles on AWS or Mapterhorn), and place searches you make go to the OpenStreetMap place search. GPX files, labels and settings are never sent.

      Elevation: Terrain Tiles on AWS (Mapzen; SRTM, 3DEP and GMTED2010 courtesy of the U.S. Geological Survey; ETOPO1 courtesy of NOAA; and regional sources listed by tilezen/joerd) or © Mapterhorn, with Copernicus WorldDEM-30 © DLR e.V. 2010-2014 and © Airbus Defence and Space GmbH 2014-2018 provided under COPERNICUS by the European Union and ESA. Place search: Nominatim, data © OpenStreetMap contributors, ODbL. The exact sources for your area appear with the preview.

      Advertisement

      Topographic map generator

      3D topographic maps from real elevation data

      The studio fetches public elevation tiles for the area you choose and turns them into a solid model with a flat base. Steep places look best; flat land needs more height exaggeration.

      Colour bands split the model by height, so a multicolour printer (or colour changes) can show water, valleys, rock and snow.

      Add a GPX trail to raise a route you walked or rode, or a label with the place name.

      Same studio, other starting points: Terrain map generator · GPX to STL.

      The method

      How to make a 3D printed terrain map

      Choose a place and the generator turns real elevation data into a solid relief: the surface follows the ground, with straight walls and a flat bottom, so it slices cleanly and prints without supports.

      1. Find the place: search for it, type its coordinates, use your location, or drag the shaded map.
      2. Set the area: how many kilometres across, and the shape of the map.
      3. Shape the relief: exaggeration, flat water, smoothing.
      4. Add colour and extras: height bands, a GPX trail, a label, a frame or plinth, a keyhole.
      5. Download an STL for one colour or a 3MF with each band as its own part.

      Data

      Where the heights come from

      Heights come from open elevation tiles, fetched for the area you choose. The default set, Terrain Tiles on AWS, blends SRTM, 3DEP and GMTED2010 (U.S. Geological Survey), ETOPO1 (NOAA) and national surveys such as EU-DEM, Canada’s CDEM, New Zealand’s LINZ and the UK Environment Agency. Mapterhorn is newer and mostly uses the 30 m Copernicus DEM. The credit line for your area appears under the studio and with the preview.

      DataTypical detailNotes
      Most of the worldAbout 30 mFrom the SRTM and Copernicus surveys
      United States3 to 10 m in many places3DEP survey
      Parts of Europe and New Zealand1 to 25 mNational surveys
      OceansHundreds of metresSea floor depths; use water at sea level for flat seas

      The generator picks the tile zoom that matches the download grid and fetches at most 64 tiles; a very large area at fine detail loads a coarser zoom and says so. Some sources measure the tops of trees and buildings rather than bare ground, and lakes can be noisy: use a set water level for a flat lake.

      Options

      Shapes and options

      OptionChoicesTip
      ShapeSquare, rectangle, circle, hexagonCircles suit a single peak; rectangles suit valleys and islands
      Width60 to 300 mmA 150 mm map shows a 20 km area at about 1 mm = 130 m
      Exaggeration×1 to ×5, or automaticMountain areas look right at ×1 to ×1.5; wide or gentle areas need ×2 to ×5
      WaterOff, sea level, or a level you setFlat water reads as a sea or lake, with a 0.6 mm step up to land
      EdgePlain block, frame, plinthThe plinth holds the label strip at the front
      TrailRaised ribbon or engraved grooveThe ribbon is its own part for a second colour
      KeyholeOn or offNeeds a 6 mm base or plinth

      Colour

      Height bands and colour changes

      With height bands on, the map is cut into horizontal slices: water, lowland, rock and snow. Each slice is its own part in the 3MF, so a multi-colour printer gives each its own filament. On a single-nozzle printer, add a colour change at each height listed under Print it well: the heights sit on 0.2 mm layer lines, so every layer above a change prints in the new colour.

      Bands start automatically at 45% and 80% of the way up, or at real heights you set, such as a tree line at 1,800 m.

      Printing

      Printing tips

      • Orientation: flat on its base, no supports. Steep cliffs print as walls.
      • Layers: 0.2 mm for most maps; 0.12 mm for gentle hills and small models.
      • Infill: 10 to 15% is plenty; the base gives the strength.
      • Trails: keep the ribbon at least 0.8 mm wide on a 0.4 mm nozzle.
      • Hanging: the keyhole’s inner chamber is a short bridge; print it as laid out.

      Privacy

      What leaves your device

      The model is built in your browser. Three kinds of request leave it:

      • Elevation tiles for the area on screen, from s3.amazonaws.com (Terrain Tiles) or tiles.mapterhorn.com. The tile addresses show roughly which area you are looking at. Tiles you have loaded are kept in this browser’s cache so they aren’t fetched again.
      • Place searches, only when you press Search or Enter, sent to nominatim.openstreetmap.org.
      • Your location, only if you press Use my location and allow it: the browser gives it to this page, and it is used like typed coordinates.

      GPX files are read on your device and never uploaded. Labels and settings stay here too; a share link carries only the settings, never the trail.

      Questions, answered

      Where does the height data come from?

      Public elevation tiles. The sources and their credits are listed further down this page.

      What exaggeration should I use?

      1.5 to 3 for mountains, more for gentle hills. The automatic setting picks a value from the area’s height range.

      How big can I print it?

      Up to 300 mm wide. Bigger areas show less detail per millimetre, so zoom in for a detailed peak.

      Is it free to use?

      Yes. No account, no watermark, no limits. The elevation data is open data, so please keep the credit line with models you share.

      Will it fit my printer?

      Choose your printer below the preview. The map width sets the size; a frame or plinth adds a few millimetres. Lower the width or the base if it’s too tall or wide.

      Can I sell maps I print?

      The designs you make are yours, and the typefaces are open-licensed, which allows making physical products. The elevation data is free to use with attribution: include the credit line shown for your area (for example on a card or listing). Check any other rules that apply to your product.

      How accurate is it?

      Distances across the map are true at its centre; heights are true to scale at ×1 and stretched by the exaggeration. The detail is limited by the data, often about 30 m between measurements, so small cliffs and buildings may not show.

      Why does my area look flat?

      Wide areas are small on the map: at 150 mm, a 100 km area puts 1 km of height at only 1.5 mm. Raise the exaggeration, pick a smaller area, or lower the base so the relief stands out.

      Sources

      Print advice is a starting point drawn from these references, checked on 2026-11-10. Community posts are one maker's experience, not a specification.

      1. Terrain Tiles on AWS (Registry of Open Data) Amazon Web Services; managed by Mapzen, a Linux Foundation project
      2. Terrain data attribution (joerd) Tilezen
      3. Mapterhorn attribution Mapterhorn
      4. Copernicus DEM: licence and attribution Copernicus Data Space Ecosystem
      5. Nominatim usage policy OpenStreetMap Foundation
      6. Copyright and licence OpenStreetMap
      7. Color change Prusa Research
      8. Mount Fuji (summit 35.36083° N, 138.72750° E) Wikipedia
      9. Mount Everest (summit 27.98833° N, 86.92528° E) Wikipedia
      10. Phantom Ranch, Grand Canyon (36.10605° N, 112.09469° W) Wikipedia
      11. Yosemite Valley (37.72167° N, 119.64639° W) Wikipedia
      12. Tenerife (28.26861° N, 16.60556° W) Wikipedia