Free generator · Runs in your browser

Medal hanger Show off every finish.

Make a medal display with your own words across the top and a row of deep hooks for ribbons. Choose the number of hooks, the spacing and the mount, and download an STL or 3MF.

  • Private by designNothing leaves this device
  • Nine kindsHooks, racks, brackets, clips
  • No supportsPrinted on its side, strong
  • Ready to sliceSTL and 3MF files

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

Hook

Make
Mounted
5
40 mm

Widened automatically if the hooks or clips would touch.

Prongs

Shape

25.0 mm

Measure the handle or cable with calipers. The clip opening is about three quarters of it, so it snaps on.

40 mm
10 mm

A wider bend is gentler on straps, towels and headbands.

14 mm

How far the tip rises above the arm. Higher keeps things from sliding off. On a shelf bracket, a lip that stops the shelf sliding forward (0 for none).

6.0 mm
16 mm

Thicker and wider hooks are stiffer. Doubling the thickness makes a hook about four times stiffer; doubling the width, about twice.

4.0 mm

A curve where the hook meets the plate spreads the load, where hooks usually crack.

Edges
40 mm

How far the saddle hangs below the desk top’s underside.

Mount

Mount

Shelf brackets are screwed to the wall, with one more screw up into the shelf.

Head sizes from DIN 7997. For other screws or a nail, choose Measured and measure the head and shank.

Measure your adhesive strip; the plate is made big enough to carry all of it.

Drop-lock pegs for pegboards with upright 5 × 15 mm slots on a 40 mm pitch.

Measure the top edge of your door.

Measure the gap between the top of the shut door and the frame. The strap is made 0.6 mm thinner.

30 mm
60 mm
5.0 mm
Print orientation

On its side, the layers run along the hook, so it is much stronger. Pegs and door straps always print on their side; racks print on their back.

Text

Separate names with commas, left to right: Sam, Ana, Leo.

12 mm
Text style
1.0 mm
Typeface

Colours

Preview

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    Medal hanger generator

    A medal hanger for your race medals

    This page opens the wall hook studio set up as a medal rack: six deep hooks under the word MEDALS. Change the words to a name, a sport or a motto like “I RUN”.

    Ribbons are wider and heavier than keys, so the hooks here are deeper with a wider opening. Space them so medals hang without touching.

    Test the rack with a few medals before loading it up, and use the wall plugs your screws need.

    Same studio, other starting points: Wall hook generator.

    The method

    How to make a wall hook

    Pick what you want to hang, how it fixes to the wall, and how big it should be. The generator builds the hook with its back plate, screw holes or mount, and any text, and lays it out ready to print.

    1. Pick the hook: a J hook, a coat hook, a row or key rack, a headphone or towel hook, a shelf bracket, a clip or an over-the-door hook.
    2. Size it: depth, opening, tip height, thickness and width.
    3. Choose the mount: screws, an adhesive strip, a keyhole for a nail, slot-pegboard pegs or a door strap. Measure your screws, strip or door.
    4. Add text if you like, then download and print it as laid out.

    Strength

    Why hooks print on their side

    A printed part is weakest between its layers. A hook printed standing up has layers across its arm, and a heavy coat can snap it along one of them. Printed on its side, every layer is a whole hook outline, so the load runs along the layers instead of pulling them apart. That is how this generator lays out single hooks, coat hooks, headphone hooks, brackets and door hooks.

    A rack of several hooks cannot lie on its side (only one hook would touch the bed), so it prints flat on its back, with tips that lean out at 45° to print without supports. Its hooks are weaker, so keep them for keys, leads and light bags, or make them thicker.

    Sizes

    Screw hole sizes

    ScrewHead (DIN 7997)Clearance holeCountersink
    3 mm5.6 mm3.5 mm6.2 mm
    4 mm7.5 mm4.5 mm8.1 mm
    5 mm9.2 mm5.5 mm9.8 mm
    6 mm11 mm6.5 mm11.6 mm
    3.5 mm6.5 mm4.0 mm7.1 mm
    4.5 mm8.3 mm5.0 mm8.9 mm

    Head diameters are the nominal sizes in DIN 7997 for countersunk wood screws with a 90° head. The hole is 0.5 mm bigger than the thread and the countersink 0.6 mm bigger than the head. For other screws, measure the head and shank and choose Measured.

    Load

    How much will it hold?

    We don’t give load ratings: a printed hook’s strength depends on the material, the walls, the printer, the wall and the fixings. The strength figure under the preview is an estimate for comparison between your own settings: stiffness grows with the width and with the square of the thickness, so a hook twice as thick is about four times as stiff.

    • Test it first with a little more than you plan to hang, and check it again after a few days: plastic creeps under a steady load, PLA most of all.
    • Fix it well: into plasterboard or masonry, use the wall plugs or anchors the screw maker recommends.
    • Adhesive strips carry what their maker says, on a clean, smooth wall, and only after their curing time.
    • Don’t hang anything valuable, fragile or dangerous over people from a printed hook you haven’t tested.

    Printing

    Printing tips

    • Material: PETG bends before it breaks and creeps less than PLA. Near heat or in sun, use PETG or ASA.
    • Walls over infill: 4 or more walls make a hook stronger than extra infill does.
    • No supports: everything is laid out to print without them.
    • Two colours: raised text is its own object in the 3MF, or pause at its first layer on one nozzle.

    Questions, answered

    How many medals fit on one hook?

    It depends on the ribbons. Make the hooks deeper, or add more hooks, if they crowd.

    Can I print a long hanger on a small printer?

    Make two shorter racks and hang them side by side, or choose fewer hooks.

    Which filament is best?

    PETG holds weight longer than PLA without creeping. Print it with plenty of walls.

    Is it free to use?

    Yes. No account, no watermark, no limits.

    Will it fit my printer?

    Choose your printer below the preview to check. A long rack prints flat, so it needs a bed as long as the rack.

    How strong is it?

    We don’t rate loads. Thicker and wider hooks are stronger, printing on the side is stronger, and PETG is tougher than PLA. Test a hook with more than you’ll hang on it before you rely on it.

    Will it fit my pegboard?

    The pegs are made for pegboards with upright 5 × 15 mm slots on a 40 mm pitch. Round-hole pegboards use a different peg.

    Can I sell hooks I print?

    The designs you make are yours. The typefaces are open-licensed, which allows making physical products. We make no claims about load or safety, so test anything you sell and don’t promise a weight it will hold.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-11. Community posts are one maker's experience, not a specification.

    1. DIN 7997: cross-recessed countersunk head wood screws, dimensions fasten.it
    2. Modeling with 3D printing in mind (orientation and strength) Prusa Research
    3. PETG Prusa Research
    4. boxes.py slot pegboard generator (slot layout) Florian Festi
    5. Slot pegboard network mounts (drop-lock peg geometry) PrimroseHA (GitHub)
    6. SIL Open Font License SIL International