Free generator · Runs in your browser

Explosion boxes Lift the lid, the sides fall open.

Make a surprise gift box whose sides fold open on print-in-place hinges when you lift the lid, showing your messages and an inner box or tiers. Download an STL or 3MF.

  • Private by designNothing leaves this device
  • Five kindsGift, explosion, ring, ornament, nesting
  • No supportsLids and hinges print as laid out
  • Ready to sliceBox, lid and bow their own objects

Drag to rotate · Scroll or pinch to zoom · Arrow keys when focused

Size
—
Filament
—
Parts
—
Fits
—

Start from

What to make

Box
Shape

A cube whose four sides fold down on print-in-place hinges when the lid lifts off, like the paper craft.

A hinged box (from the box generator) with a cushion that holds a ring upright in a slot.

Size

Measure the gift with calipers or a ruler and type its size.

1.0 mm

Added on every side and on top. The inside is the gift plus this room; 0 makes the inside exactly the size you typed.

1.0 mm
60 mm

The sides lie flat around the base to print, about three times this wide: pick your printer below the preview to check it fits.

Inside

Measure across the ring, stone included, with calipers.

The slot is 0.6 mm wider than this.

2.0 mm
0.30 mm

The gap between the lid and the box, and in the hinges. 0.3 mm suits most printers; raise it if parts fit too tightly.

Name and decoration

Name on the lid

A raised name means the lid prints the right way up, with a groove underneath that drops over a neck on the box.

Typeface
Topper

Ornament boxes carry a hanging loop instead of a bow.

10 mm

Colours

Preview

Download

Building the preview…

Print it well

    Everything is built on this device. Nothing you type or upload is sent anywhere.

    Advertisement

    Explosion box maker

    How the printed explosion box opens

    This page opens the gift box studio set up as an explosion box. The base and four sides print flat in one piece with the hinges already in place, and the lid holds the sides up until you lift it.

    Messages are raised on the inside faces, so they read the right way up when each side falls open.

    Bigger boxes need a bigger printer bed when laid flat; the studio warns when it will not fit.

    Same studio, other starting points: Gift box generator.

    The method

    How to make a printed gift box

    Measure the gift, pick a shape, and the generator builds a box whose inside is the gift plus the room you choose, with a lid that fits it, a name on top and a bow or ribbon groove.

    1. Pick what to make: a gift box, an explosion box, a ring box, an ornament box or a nesting set.
    2. Size it from the gift: measure with calipers or a ruler, or pick a gift card.
    3. Add a name and a bow, or messages inside an explosion box.
    4. Download and print. Box, lid and bow are separate objects, so each takes its own colour.

    Sizes

    Gift sizes

    Only the gift card and the banknote have published sizes. The others are starting points: measure your gift and type its size.

    GiftStarting sizeWhere it comes from
    Gift card85.60 × 53.98 mmISO/IEC 7810 ID-1 card size
    Cash roll66.29 mm longA rolled US banknote (6.14 × 2.61 in); measure the roll’s thickness
    Ring40 × 40 × 28 mmStarting size; the ring box sizes itself from the ring
    Watch70 × 70 × 40 mmStarting size; measure it
    Earrings45 × 35 × 16 mmStarting size; measure them on their card
    BoxLidHow it prints
    Gift box, name cut inLift-off lid with a lip inside the boxLid upside down, no supports
    Gift box, raised nameLift-off lid with a groove over a neck on the boxLid right way up, no supports
    Explosion boxA cap over the four sidesBase and sides flat, hinges in place
    Ring boxHinged lid (print in place)Box with the lid open, cushion apart
    Ornament boxLift-off lid with a hanging loopLid right way up
    Nesting setAs the gift boxThree boxes, each round the next

    Printing

    Printing tips

    • Hinges need their clearance: print a clean, unsquashed first layer and flex the hinges gently once cool. If they fuse, print a clearance test first.
    • Print the lid upside down when the name is cut in: the top comes out smooth on the bed.
    • A second-colour name on one nozzle: add a colour change at the layer the studio gives.
    • Lid too tight or loose? Change the clearance by 0.05 mm and reprint the lid only.
    • Small parts: bows and small boxes are not for children under 3.

    Questions, answered

    Do the hinges need assembly?

    No. They print in place; work them gently after printing to free them.

    How big can it be?

    The flat layout is about three times the box width, so a 60 mm box needs a bed a little over 180 mm.

    Can I add my own messages?

    Yes, one on each inside face, plus a name on the lid.

    Is it free to use?

    Yes. No account, no watermark, no limits.

    Will it fit my printer?

    Choose your printer below the preview. An explosion box lies flat at about three times its width, so a smaller cube may be needed on small printers.

    Can I sell boxes I print?

    The designs you make are yours. The typefaces are open-licensed, which allows making physical products. Small parts need care: check toy-safety rules before selling for children.

    Will a gift card fit?

    Yes: the gift card preset uses the ISO/IEC 7810 ID-1 size, 85.60 × 53.98 mm, plus the room you choose all round.

    Sources

    Print advice is a starting point drawn from these references, checked on 2026-11-12. Community posts are one maker's experience, not a specification.

    1. ISO/IEC 7810 (ID-1 card size) Wikipedia
    2. ISO/IEC 7810:2003 Identification cards: physical characteristics ISO
    3. U.S. currency: the basics (note size) U.S. Currency Education Program
    4. Color change Prusa Research
    5. SIL Open Font License SIL International